Manual Angelcare AC301 (page 5 of 13) (English, French)

537058

Zoom out

Zoom in

1/13

Warnings

• This product is NOT a medical device nor a device to prevent cases of

Sudden Infant Death Syndrome (SIDS).

• This product is NOT a substitute for direct super

vision of your baby

Check your baby’s activities at regular intervals. Monitoring of

premature babies, or those considered to be at risk, should be carried

out only under the supervision of a doctor or health professional.

•Please make sure you DON'T put the Parent Unit near wireless devices

and microwave ovens. This may disrupt the transmission of the alarm

signal

• The Sensor Pad may detect movement from many sources from both

inside and outside your baby’s room, for example: fans, washing

machines, loud music, etc. Ensure that all vibration sources are

eliminated before using the Angelcare

Monitor. Avoid contact

with crib when monitor is in use. Refer to the Movement

Sensitivity Adjustment and Troubleshooting section.

• ALWAYS place both units on flat surface in an upright position, away

from baby’

s reach.

• DO NO

T touch the end of the ada

pter cord when plugged into an

electrical outlet.

• The Angelcare

Monitor uses public airwaves to transmit signals. The

Parents Unit may pick up signals or interference from other nursery

monitors in your area. Your monitor may even be picked up by other

households. To protect your privacy, make sure both units are in the

OFF position when not in use.

• This product should be serviced by qualified personnel. There are no

user serviceable parts inside monitor. Refer all service questions to

your distributor (see page 14).

Instructions

RETAIN INSTRUCTIONS: Keep user’s manual for future reference.

WATER, MOISTURE AND HEAT DAMAGE: Keep all components away

from water (sink, bath tub, swimming pool) and places that emit heat

(stove, radiator).

VENTILATION: ALWAYS place both units on flat surface in an upright

position so that air can flow freely around them.

AC POWER SOURCE: Use only the AC adapters supplied with the

Angelcare

Monitor.

CORD PROTECTION: Avoid damage to the cords of the Sensor Pad and

adapters. Route cords so that they are not likely to be walked on or

pinched by items placed upon or against them.

CLEANING: Disconnect all units before cleaning. DO NOT immerse in

water. Use a dry cloth to keep monitor free from dust. DO NOT spray with

cleaning products or solvents. Wipe Sensor Pad with a very slightly

damp cloth with an antiseptic or mild detergent.

OBJECT AND LIQUID ENTRY: Care should be taken so that objects do

not fall onto units and that liquids are not spilled into either unit or

Sensor Pad through its openings.

NON-USE PERIODS: When not using monitor for long periods, remove

the batteries from both units and disconnect the AC adapters from

electrical outlet.

Testing Your Angelcare

Monitor

Note: Test your Angelcare

Monitor BEFORE first-time use and then

on a periodic basis.

The Angelcare

Monitor can be used outside of the crib, in a different

sleeping area. Test monitor when moving Sensor Pad to a new location

to ensure sensitivity is adjusted correctly to the new padding or

mattress. Consult the Movement Sensitivity Adjustment section.

Step 1. On the Nursery Unit, switch to the “Sound Only” function.

Have someone else speak into the Nursery Unit or place a radio near

Nursery Unit. You should hear sound from the Parents Unit. If there is no

sound, refer to the Troubleshooting section.Make sure that both units are

on the same channel, either on A,

B or C. If reception is not clear,

switch to other channel.

Step 2. Test monitor to detect movement. Switch Nursery Unit to the

“Movement” function. Gently move your hand on the mattress. The

green light will continue to flash with your every movement. Remove

hand from mattress. Due to no movement, a “pre-alarm Tic” sound will

emit after 15 seconds. 5 seconds later, the alarm will sound and the red

light will flash continuously.

NOTE: If alarm does not sound,the Sensor Pad may be detecting a continuous

vibration from the floor, a strong draft or the crib is being touched. Avoid

contact with crib when monitor is in use. Place crib near a solid supporting

wall and away from strong air currents.The sensitivity of the Sensor Pad may

need to be reduced, consult the Movement Sensitivity Adjustment section.

Step 3. To stop alarm, place your hand lightly on mattress for Sensor

Pad to redetect movement. The red Alarm indicator light on the Nursery

Unit will continue to flash 1 minute (Figure 3).

Step 4. Verify that the battery mode is functional by operating both units

without the AC adapters. The green Power light should appear on both units.

Parents Unit: When orange Low Battery indicator light appears, replace

batteries promptly for Model AC301. For Model AC301-R, recharge

Parents Unit for 12 hours.

Nursery Unit: When orange Low Battery indicator light appears a rapid

“clicking” is heard, the temperature indicator turns off and a beep will

sound every 30 seconds, replace batteries promptly. If not, the light will

eventually turn red and the monitor will stop working.

Operating Tips

Movement Sensitivity Adjustment

The Sensitivity Adjustment Dial has been preset to suit

most situations. However in certain circumstances,

the sensitivity may not be ideal. DO NOT increase sensitivity unless false

alarms occurs and you have followed the advice in the Troubleshooting

section for false alarms. Make a note of the pre-set position of the dial

should you wish to return to it.

The Alarm Indicator Light on the Nursery Unit will flash red and beep

once when monitor barely detects movement. This could be a result of:

baby being in a very deep sleep or baby having moved away from

Sensor Pad to edge of crib. If alarm does NOT sound, no adjustment of

sensitivity is required. If the alarm indicator light flashes red most of the

time with baby directly over the location of either Sensor Pad, a false

alarm may occur. If this happens, adjust the sensitivity.

To adjust sensitivity, increase dial to the next setting. Retest monitor.

Channel selection for sound reception

Make sure that both units are on the same channel, either on A, B or

C. If reception is not clear, switch to another channel. If interference

persists, consult the Troubleshooting section.

Green Sound Lights

The three Sound Lights allow you to see baby’s sounds. The louder the

sounds from baby, the more lights appear.

Temperature display

The Nursery Unit is equipped with room temperature display. The

temperature is displayed in Celsius (C).

Night light halo

Press on the first light at the top of the Nursery Unit to activate the night light.

Voice activated

This monitor is equipped with a voice activated system.The nursery unit will

be activated and transmit sounds to the parents unit only when it captures

sound. This will make sure that the parents unit will only respond to its

matching nursery unit.

ManAC301 angl-fra 14 july06.qxd 7/14/06 9:29 AM Page 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Angelcare AC301 in the language / languages: English, French as an attachment in your email.

The manual is 1,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Angelcare AC301

Angelcare AC301 User Manual - German, Dutch, Danish, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 72 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Angelcare AC301 Manual

Product: