537059
5
Zoom out
Zoom in
Previous page
1/48
Next page
Problem Possible Cause Solution
False alarms
Alarm will not sound
Alarm indicator light is flashing red
(monitor is barely detecting
movement)
Power ON indicator does not light up
TROUBLESHOOTING
Baby was removed from crib and Monitor was not
switched OFF .
Sensor Pad cord not connected properly to Monitor.
Sensor Pad is not in full contact with crib mattress, or crib
mattress is not resting on a completely flat or rigid surface.
Baby has moved away from Sensor Pad, to the edge of the crib.
• Monitor is detecting movement when crib is being touched.
Monitor is detecting movement from outside the crib such as
motorized devices, strong drafts, etc.
• Sensitivity is set too high.
Sensor Pad is not in full contact with crib mattress, or crib
mattress is not resting on a completely flat or rigid surface.
Baby is in a very deep sleep or has moved away from Sensor
Pad, to the edge of the crib.
• Batteries are low or improperly installed.
• The Monitor is not ON.
• Turn Monitor to the OFF position.
• Verify the connection between the Sensor Pad and Monitor.
Unplug and reconnect the cord.
• Make sure there is no bedding between mattress and Sensor
Pad. Sensor Pad must rest on a completely flat and rigid surface.
If your crib has a flexible or uneven base (metal spring base,
etc.), place a piece of 6 mm (1/4") plywood to cover the full size
of the crib base.
• Make sure Sensor Pad is positioned as described in the 4
Easy Steps section. Sensitivity may need to be adjusted,
consult the Movement Sensitivity Adjustment section.
Avoid contact with the crib when monitor is ON.
Place crib near a solid supporting wall to avoid Sensor Pad
from detecting movement from outside crib.
You may need to decrease the sensitivity, consult the
Movement Sensitivity Adjustment section.
Make sure there is no bedding between mattress and Sensor
Pad.Sensor Pad must rest on a completely flat and rigid surface:
place a piece of 6 mm (1/4”) plywood to cover the full size of the
crib base.
Make sure Sensor Pad is positioned as described in the 4
Easy Steps section. Sensitivity may need to be adjusted,
consult the Movement Sensitivity
Adjustment section.
Check / replace ba
tteries.
• Check connections or change to another electrical outlet.
• Make sure Monitor is ON.
Testing Your Angelcare
®
Monitor
NOTE: Test your Angelcare
®
Monitor BEFORE first-time use and
then on a periodic basis.
The Angelcare
®
Monitor can be used outside of the crib, in a different
sleeping area. Test monitor when moving Sensor Pad to a new location
to ensure sensitivity is adjusted correctly to the new padding or
mattress. Consult the Movement Sensitivity Adjustment section.
Step 1 Switch the power and “Tic” function to the ON positions. Gently
place your hand on the mattress. The green light will continue to flash
with your every movement. Remove hand from mattress. Due to no
movement, a “pre-alarm Tic” sound will emit after 15 seconds. 5
seconds later, the alarm will sound and the red light will flash
continuously.
NOTE: If alarm does not sound, the Sensor Pad may be detecting a
continuous vibration from the floor, a strong draft or the crib is being
touched. Avoid contact with crib when monitor is in use. Place crib near
a solid supporting wall and away from strong air currents. The
sensitivity of the Sensor Pad may need to be reduced, consult the
Movement Sensitivity Adjustment section.
Step 2 To stop alarm, place your hand lightly on mattress for Sensor
Pad to redetect movement.The red Alarm indicator light on the Monitor
will continue to flash 1 minute (Figure 3).
Step 3 When Monitor produces a rapid “clicking” sound, replace
batteries promptly.
Movement Sensitivity Adjustment
The Sensitivity Adjustment Dial has been preset
to suit most situations. However in certain
circumstances, the sensitivity may not be ideal. DO
NOT increase sensitivity unless false alarms occurs
and you have followed the advice in the
Troubleshooting section for false alarms. Make a note
of the pre-set position of the dial should you wish to
return to it.
The Alarm Indicator Light on the Monitor will flash red when Monitor
barely detects movement. This could be a result of: baby being in a very
deep sleep or baby having moved away from Sensor Pad to edge of crib.
If alarm does NOT sound, no adjustment of sensitivity is required. If the
Alarm Indicator Light flashes red most of the time with baby directly over
the location of either Sensor Pad, a false alarm may occur. If this
happens, adjust the sensitivity.
To adjust sensitivity, increase dial to the next setting. Retest monitor.
5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Angelcare AC300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Angelcare AC300 in the language / languages: All languages as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Angelcare AC300

Angelcare AC300 User Manual - English - 60 pages

Angelcare AC300 User Manual - English - 10 pages

Angelcare AC300 User Manual - German, Dutch - 60 pages

Angelcare AC300 User Manual - Dutch - 16 pages

Angelcare AC300 User Manual - Dutch - 5 pages

Angelcare AC300 User Manual - French - 60 pages

Angelcare AC300 User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info