681983

Angelcare AC201-2P Manual

11
Zoom out
Zoom in
Previous page
1/56
Next page
11
Setting Up Your Monitor
Sensor Pad Sensor Pad
CORRECT
INCORRECT
CORRECT
Sensor Pad centered printed side up
INCORRECT
Sensor Pad off center
INCORRECT
Sensor Pad printed side facing down
POSITION OF SENSOR PAD UNDER MATTRESS (Top Down View of Crib)
PLACEMENT OF SENSOR PAD CORD
Figure 1
Figure 2
SENSOR PAD (See figs. 1 and 2)
• Connect the Sensor Pad cord to the Nursery Unit.
• Place the Sensor Pad in the middle of the crib under the mattress, as illustrated below. Make sure the printed side faces up. Do NOT
place any bedding between the mattress and the sensor pad.
• Secure the sensor pad cord to crib using a tie wrap. Run the cord on the floor to ensure it is out of the baby’s reach.
• The Sensor Pad must rest on a completely flat and firm surface. If the crib has a spring or slat base, place a hard board between the
crib base and the Sensor Pad measuring at least 13” x 13” (33x33 cm) and 1/4 inch (6 mm) thick. Make sure the sensor pad’s cord
passes underneath the mattress as shown below.
• The sensor pad works with all baby bed sizes and all mattresses, except memory foam mattresses. You will have to test your sensor
pad on p.16.
• Once you are done using the Sensor Pad, please remove it from the baby’s crib and store it away.
• The Angelcare Sensor Pad feature is not designed for use with adults, children or infants older than 24 months.
Movement Sensitivity Control
Figure 3
IMPORTANT: Only use the AC adapters included with your monitor. Do not use these adapters with any
other equipment. Movement Sensitivity Control. The movement sensitivity control is on the back of the
Nursery Unit. The level has been preset to suit most conditions of movement detection (see fig.3). Do not
adjust this unless you receive false alarms. Refer to the Movement Sensitivity Adjustment section on for
more information. It is extremely important to follow our instructions for setting the sensitivity level. Now
plug the Sensor Pad cord into the jack on the back of the Nursery Unit marked “Sensor Pad.” Turn the
Nursery Unit on using the switch on the left. The green Power Indicator will light up.
WARNING
STRANGULATION HAZARD - Children have STRANGLED in cords. Keep the adapter cords
and sensor pad cord out of the reach of children. Do not put the Nursery Unit inside a
crib or play yard. Because of the serious strangulation risk to infants and toddlers, par-
ents and caregivers should never place the nursery unit within 3 feet (1 meter) of a crib.
NEVER use extension cords with AC adapters. ONLY use the AC adapters provided.
IMPORTANT
Keep at
least 1m
(39 inches)
apart
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Angelcare AC201-2P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Angelcare AC201-2P in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 2,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info