541774
12
Zoom out
Zoom in
Previous page
1/20
Next page
SVT-VR Bass Guitar Amplifier
12
Power tubes
are the largest tubes used in an amplifier, generate the most heat and wear out the fastest.
These tubes convert the low-level, conditioned signal from the preamplifier into a level that is sufficient to
drive the speakers. There are several types of power tubes available, each of which offers a different per-
formance/sound characteristic. For example, the EL34 power tube produces a great classic rock sound.
When an EL34 is driven into distortion, it produces a unique sound (“crunch”). When compared to the 6L6,
the EL34 distorts more quickly, exhibits a “looser” low-end response and produces more harmonics at mid
and high frequencies (“creamier” sound). These differences become more noticeable at higher volumes.
The 6L6 tubes produce a big low-end thump and have very good dynamic range. They offer a more tradi-
tional “American Rock” sound. The 6V6 tubes produce a creamy sound with nice distortion. On the other
hand, the KT88 produces a big low-end but sounds more like an EL34 in the mid and high frequencies.
The 6550 power tubes are more rugged and stay cleaner sounding, even at full power. When they do dis-
tort, the sound produced is more solid and has a tighter low end; more of a “heavy metal” type distortion
with lots of power.
Some power tubes are available in matched sets. These tubes have been extensively tested for optimum
performance and longevity.
When replacing power tubes, please replace them with a tested, matched pair and have the amp rebiased
by a qualified service center. It is possible to change the sound of the amplifier by changing the type of
power tubes. When making any modification to your equipment, it is highly recommended that you consult
with a qualified service center.
The nature of tubes – why (and when) to replace them:
Tubes are made up of a number of fragile mechanical components that are vacuum-sealed in a glass
envelope or bubble. The tube’s longevity is based on a number of factors which include how hard and
often the amplifier is played, vibration from the speakers, road travel, repeated setup and tear down, etc.
Any time you notice a change in the amplifier’s performance, check the tubes first.
If it’s been awhile since the tubes were replaced and the sound from the amplifier lacks punch, fades in
and out, loses highs or lows or produces unusual sounds, the power tubes probably need to be replaced.
If the amplifier squeals, makes noise, loses gain, starts to hum, lacks “sensitivity”, or feels as if it is
working against you, the preamplifier tubes may need to be replaced.
The power tubes are subjected to considerably more stress than the preamplifier tubes. Consequently,
they almost always fail/degrade first. If deteriorating power tubes aren’t replaced, they will ultimately fail.
Depending on the failure mode, they may even cause severe damage to the audio output transformer
and/or other components in the amplifier. Replacing the tubes before they fail completely has the potential
to save time, money and other unwanted troubles. Since power tubes work together in an amplifier, it is
crucial that they (if there is more than one) be replaced by a matched set. If you are on the road a lot, we
recommend that you carry a spare matched set of replacement power tubes and their associated driver
tubes.
After turning off the power and disconnecting the amplifier from the power source, carefully check the
tubes (in bright light) for cracks, white spots inside the glass or any apparent damage. Then, with the
power on, view the tubes in a darkened room. Look for the preamplifier tubes that do not glow at all or
power tubes that glow excessively red.
Tube types and usage continued...
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ampeg SVT-VR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ampeg SVT-VR in the language / languages: English as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info