541765
5
Zoom out
Zoom in
Previous page
1/12
Next page
SVT-CL Bass Guitar Amplifier
5
The Front Panel
1. 0 dB INPUT: The signal output from a
passive instrument may be connected to
this 1/4" input by means of a shielded
instrument cable.
2. -15 dB INPUT: The signal output from
an active instrument may be connected
to this 1/4" input by means of a shielded
instrument cable.
3. GAIN: This control adjusts the basic
level of signal in the preamp.
4. ULTRA HI: This switch, when engaged,
enhances the amount of high frequency
output by 9 dB at 8 kHz.
5. ULTRA LO: This switch, when engaged,
enhances the amount of low-end output
by 2 dB at 40 Hz and -10 dB cut at
500 Hz.
6. BASS: Use this to adjust the low
frequency level of the amplifier. This
provides up to 12 dB of boost, or
12 dB of cut at 40 Hz. The low
frequency output is flat at the center
position.
7. MIDRANGE: Use this to adjust the
midrange frequency level of the
amplifier. This provides up to 10 dB of
boost, or 20 dB of cut at the selected
frequency [8]. The midrange frequency
output is flat at the center position.
Rotate the control counter-clockwise
for a “contoured” sound (more distant,
less midrange output) or clockwise for a
sound which really cuts through.
8. FREQUENCY: This control allows you
to select the center frequency for the
midrange control [7], giving you a
choice of five “voices” for the midrange.
The numbers correspond to the
following center frequencies:
1=220 Hz, 2=450 Hz, 3=800 Hz,
4=1.6 kHz, 5=3 kHz.
9. TREBLE: Use this to adjust the high
frequency level of the amplifier. This
provides up to 15 dB of boost, or
20 dB of cut at 4 kHz. The high
frequency output is flat at the center
position.
10. MASTER: Use this to control the
overall output level. It affects the
speaker outputs and the preamp
output [20]. Use it wisely, and turn
it down when making connections
or trying something new.
11. STANDBY/POWER/FAULT INDICATOR
LED: This is a multi-function LED. In
Standby mode, it glows red. In the On
mode (when the high voltage comes on)
it glows green. If it does not turn green
in the On mode, there is no high voltage
present and the unit needs to be
serviced. If the amp detects a fault in
the power tube circuit, the high
voltage is turned off and the LED flashes
between red and green. This usually
indicates a bad power tube. The amp will
remain in this condition until the unit is
turned off.
1 2 3 4 5 6 7 8 9 10 11 12 13
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ampeg SVT-CL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ampeg SVT-CL in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info