541764
8
Zoom out
Zoom in
Previous page
1/16
Next page
SVT-3 PRO Bass Guitar Amplifier
8
28
CAUTION:
TO
REDUCE THE RISK
OF FIRE, REPLACE
FUSE WITH SAME
TYPE AND RATING.
SPEAKER OUTPUTS
AC LINE IN
ATTENTION:
UTILISER UN FUS-
IBLE DE RECHANGE
DE MEME TYPE.
110/115V: 250V T10A SLO BLO
230V: 250V T5A SLO BLO
MODEL:
SERIAL:
LINE: V ~ Hz
WATTS: MAX
SVT-3PRO
120 XX
1000
CAUTION
RISK OF ELECTRIC
SHOCK - DO NOT OPEN
RISQUE DE CHOC
ELECTRIQUE
NE PAS OUVRIR
TO REDUCE THE RISK
OF FIRE OR ELECTRIC
SHOCK, DO N OT EX-
POSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
AVIS:
275 WATTS @ 8 OHMS
450 WATTS @ 4 OHMS
4 OHM MIN. LOAD
EFFECTS LOOP
TUO RENUTLEVEL
RETURN SENDPOWER AMP
IN
PREAMP
OUT
FOOTSWITCH
PRE
PULL
GROUND
LIFT
POST
29 30 31 32 33 34 35
3222 2726252421
BALANCED
TRANSFORMER BAL. LINE OUTPUT
BALANCED/
UNBALANCED
21. SPEAKON
®
JACK: Use of this heavy-
duty connector is recommended when
playing at full output levels due to
its incredibly high current handling
capability. Connect the amplifier to
the speaker cabinet(s) using heavy
gauge speaker cables terminated
with the appropriate connectors.
The pin connections for this jack are:
1+ = positive
1– = negative
22. RACK SUPPORT FASTENER: For
the most secure rack installation, it is
recommended that a supplemental sup-
port be fabricated and fastened to the
amplifier via this threaded insert. Use a
1/4–20 threaded bolt that will not pro-
trude more than 1/2" into the amplifier
to connect the strap.
23. LINE OUTPUT LEVEL / GROUND
LIFT: This control adjusts the output
level at both line output jacks. This
control works independently from the
front panel master control. If necessary,
pull this knob to engage the ground lift
and eliminate hum.
24. POST-EQ / PRE-EQ: The signal at
the line out jacks can be set to either
Pre-EQ or Post-EQ with this switch.
With the switch in the OUT position,
the signal at the jacks is Pre-EQ. This
is a direct output not affected by any
EQ or boost settings. With the switch
in the IN position, the signal is
Post-EQ and is controlled and
modified by the tone controls,
Graphic EQ and the effects loop.
25, 26. TRANSFORMER BALANCED
LINE OUTPUTS: These jacks supply
a balanced/unbalanced preamp output
signal for connecting to a house mixing
board, recording console or external
amplifiers with balanced inputs. The
signal can either be set to Pre- or Post-
EQ with the selector switch and its level
is controlled by the line out level control.
27. TUNER OUT: This jack supplies the
only live output when the mute switch
is engaged. This allows for silent tuning
through an electronic tuner or killing the
house send with a monitor mixer send
still active.
28. FUSE: The fuse protects the unit from
damage due to overload conditions or
AC power line surges. If the fuse blows,
replace it only with the same size and
type.
(Speakon
®
is a registered trademark of Neutrik AG.)
The Rear Panel
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ampeg SVT-3 Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ampeg SVT-3 Pro in the language / languages: English as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info