541757
15
Zoom out
Zoom in
Previous page
1/20
Next page
PF-350 / PF-500 / PF-800 Bass Guitar Amplifier
15
PF-500 / PF-800 Rear Panel continued
19 20 21 22 23 23 24 2625 27 28
2930313233
XLR line
out
pre-EQ
post-EQ
300 W @ 8 500W @ 4Ω MIN LOAD [PF-500]
400 W @ 8 800W @ 4Ω MIN LOAD [PF-800]
send
return
tuner outpwr amp in pre amp out
patch
power
LIFT
GND
-40dB
0dB
ft switch
speaker outputs
CLASS 2 WIRING
fx loop
PF 800
PF 500
25. GROUND / LIFT: Press this switch in to
engage the Ground Lift, if necessary, to
help eliminate hum at the XLR jack.
26. 0 dB (line level) / -40 dB (mic level):
Press this switch in to apply a –40 dB
cut to the signal at the XLR Line Out
[24].
27. POST-EQ/PRE-EQ: The signal at the
XLRLineOut[24]canbesettoeither
Pre-EQ or Post-EQ with this switch. With
the switch in the IN position, the signal
at the XLR Line Out is Pre-EQ. This is a
direct output not affected by any EQ or
boost settings. With the switch in the
OUT position, the signal is Post-EQ and
is controlled and modified by the tone
controls, and the effects loop.
28. FX SEND JACK:Usethis1/4"TS
unbalanced output to send a line-level
output to an external effects processor
(for example). The output here is
affected by all controls except the
volume.
Use the FX return jack to feed the
returned processed signals back into the
power amplifier.
29. FX RETURN JACK:Usethis1/4"TS
unbalanced input to return the
processed line-level output of an external
effects processor (for example). The
processor could be fed by signals from
theFXsend[28].
30. TUNER OUT: This jack supplies the
only live output when the mute switch
is engaged. This allows for silent tuning
through an electronic tuner or killing the
house send with a monitor mixer send
still active.
31. PREAMP OUT: This jack is a direct
post master preamp output for use with
an external power amp. Connect the
external amp’s input to this jack using a
shielded instrument cable.
32. POWER AMP IN: This jack connects
directly to the internal power amp for
use with an external preamp. When
using an external source, connect the
OUTPUT of the source to this jack using
a shielded instrument cable to feed the
signal into the power amp section. The
internal signal is disconnected when a
plug is inserted into this jack.
33. FOOTSWITCH: Connect a dual
footswitch to this jack for remote Mute
and FX On/Off control. On the stereo
1/4"plug,thetipcontrolsMuteand
the ring controls FX On/Off. The Mute
function is available from either the front
panel or the footswitch.
NOTE: A footswitch may be purchased at
your local Ampeg Dealer or ordered
directly from LOUD Technologies Inc. Be
sure to ask for model #AFP2.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ampeg PF350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ampeg PF350 in the language / languages: English as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info