496064

Amica UKS 16158 Manual

76
Zoom out
Zoom in
Previous page
1/80
Next page
76
EN
DOOR REVERSAL
6. Remove the two screws, which attach the lower hinge to the appliance door (Fig. 5). Take
special care and hold the appliance door with the other hand.
7. Holding the door, swing the lower door hinge away from the door using the other hand, then
detach the door from the appliance body (Fig. 6).
8. Remove the two screws , which attach the upper hinge to the body and the two screws hol-
ding the lower hinge to the appliance body (Fig. 7).
9. Screw the upper and lower hinge on the opposite side of the appliance body using suitable
screws (Fig. 8). Upper hinge should be mounted on the other side of the appliance as the lower
hinge. The lower hinge should be mounted on the other side of the appliance as the upper
hinge.
With the hinges open, hold the door parallel to the appliance body and screw the hinges to the
door using suitable screws while taking proper care.
10. Make sure that the door is properly aligned with the appliance body (Fig. 9).
INSTALLATION OF THE APPLIANCE
Installation of the appliance should be performed by a qualied installer. The appliance should be
placed in furniture case (Fig. 10). Once the appliance is placed correctly, adjust the height of the ap-
pliance by turning the 4 adjustable feet as appropriate. If necessary, adjacent Amica appliances sho-
uld be braced with a bracket xed by screws and tted in furniture (Fig. 11). There is a special strip
at the top of the appliance. Attach it to the underside of the cabinet with appropriate screws supplied
with the assembly kit (Fig. 16). Decorative strip must not block the vents located in the bottom casing
unit, the strip must be cut to size (Fig. 17). The depth of the bottom casing unit can be adjusted by
moving it forwards or backwards. Once properly adjusted, tighten the mounting screws (located in
the openings on both sides of the casing unit) with a cross-head screwdriver. This will permanently
attach the casing unit (Fig. 18).
FITTING FURNITURE BOARD TO APPLIANCE DOOR
Place the mounting bracket on furniture board and position it accordingly (Fig. 12). The distance between
the furniture board and the underside of the worktop should be 5 mm (Fig. 13). Attach the mounting
bracket using suitable screws supplied in the installation kit. Pull out the mounting bracket cover and
screw in the two special screws (2) in the appliance doors(Fig. 14). Attach furniture board with the xed
mounting bracket to the appliance door. Secure the furniture board with suitable nuts (item 3, Figure
14). Make sure the furniture board assembly is positioned correctly relative to the appliance (Fig. 15).
Using the supplied screws, attach the furniture board assembly to the bottom of the appliance door
(Fig. 15). Replace the mounting bracket cover in its original location.
1. Unplug the appliance before reversing the door opening direction.
2. Remove food from the appliance.
3. Remove caps on the front of the refrigerator body (Fig. 1, Fig 2).
4. Remove the two screws, which attach the upper hinge to the appliance door (Fig. 3). Take spe-
cial care and hold the appliance door vertically.
5. Holding the door, swing the upper door hinge away from the door using the other hand (Fig. 4).
Beespeciallycarefulduringthisstep,asthehingemaycloseandcauseinjury.
… 76 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Amica UKS 16158 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Amica UKS 16158 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info