541299

Amica IH 17200 E Manual

32
Zoom out
Zoom in
Previous page
1/36
Next page
32
V INSTALLATION
Connecting to the power network and operation check
After connecting the device to the power supply network (in accordance with the requirements dened
above) it is necessary to check operation of the motor and lighting of the hood.
Setting the operation mode of the kitchen extractor hood
Setting the air extractor mode of operation of the hood
When cooker hood operates in extraction mode, air is discharged outside through an extraction duct.
The cooker hood is connected to the air outlet opening using a rigid or exible extraction duct with a
diameter of 120 mm, and the appropriate clamps, which must be purchased at a hardware store. Con-
nect one end of the duct to the ange (Fig. 9), and the other to the air outlet hole. Proper duct routing
is shown in Fig. 8. A qualied installer should be commissioned to make the connection.
Setting the odour absorber mode of operation of the hood
In this setting the air is ltered and returned back to the room through openings located in the upper part of the body
of the hood. Install activated charcoal lter in this setting (see the manual for details on installation).
Fan speeds
The lowest and medium speeds should be used under normal conditions and with low concentration of
fumes. The top speed should be used in case of high concentration of kitchen fumes, e.g. during frying
or grilling.
EN
Install the cooker hood on the ceiling:
1. Open the aluminium lter cover (on selected models-Figure 3) and remove the aluminium grease lter (for lter
removal description please refer to other section of this manual).
2. The distance between the hob and the motor body must should be at least 84 cm (Fig. 4).
3. Remove the mounting screws (Fig. 5) and set the unit at the correct height and then tighten both parts of the
hood.
4. Place mounting template on the ceiling where the hood is to be mounted. Drill holes A, B, C, D with a 10 mm drill
and insert the wall plugs in them. Insert the screws 5.5 x45YSB leaving a 5mm gap between the screw head and
the ceiling. Place the hood body on the ceiling so that the heads of the screws go through the mounting holes.
Now turn the hood body clockwise so that it is locked and permanently xed to the ceiling. Tighten the mounting
screws (Figure 6).
The wall plugs provided are not universal. If the ceiling structure requires a different type of anchors, purchase
them at a DIY store.
5. If the cooker hood will operate in extraction mode, connect the duct (Fig. 8) to the outlet installed earlier on (Fig.
9). Make sure that the duct is properly tted and that operating the hood at the highest speed will cause the duct
to detach from the nozzle.
6. Insert the upper masking frame and secure it with the screws (Fig. 10).
7. Slide the cover body (Figure 11) in and turn it clockwise until it locks in place (Fig. 12).
8. Connect the wiring harnesses for lighting and the control panel (Figure 13). In addition, connect the lighting
wiring harnesses.
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Amica IH 17200 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Amica IH 17200 E in the language / languages: English, German, Polish as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info