795030
11
Zoom out
Zoom in
Previous page
1/20
Next page
11
OPERATION AND FUNCTIONS
Control panel (Fig. 10).
1. Red LED- Shows that the appliance is supplied with electric energy.
2. Green LED- Shows that the compressor is working.
3. Temperature adjustment knob
Temperature adjustment
Turning the knob to a different setting changes the temperature in the fridge-freezer.
Available knob settings:
• appliance switched off - OFF setting
• maximum temperature - 1 setting
• optimal temperature - 2-4 setting
• minimum temperature - setting
Do not put food into the fridge freezer befo-
re it has reached its operating temperature,
which takes minimum 4 hours.
Temperature inside the fridge / freezer chamber
Do not change the temperature settings due to the change in the season of the year. The ambient tem-
perature increase will be detected by the sensor and the compressor will be switched on automatically
for a longer period of time in order to maintain the temperature set inside the chambers.
Minor changes in temperature
The slight changes in temperature are perfectly normal and may occur, for instance during the storage
of great quantities of fresh products in the fridge, or when the door is open for a longer period of time.
This will not affect the condition of the stored foodstuff, and the temperature will quickly return to its set
value.
Replace the light bulb*
Set the knob to „OFF”, then unplug the appliance.
Remove the bulb cover (Fig. 18).
Replace the bulb with one having identical parameters as the bulb factory pre-installed in the ap-
pliance (E14 thread, 220-240V, max 10W, maximum dimensions: diameter 26 mm, length 55 mm).
Replace the bulb cover.
Bulbs of a higher or lower power should not be used, only use bulbs of the specication given
above.
The light bulb must not be used for room illumination.
* Applicable to appliances factory designed for incandescent lighting, and selected appliances equip-
ped with LED lighting in the form of a E14 thread light bulb.
In order to defrost the freezer chamber, you must take the following steps (Fig. 20):
Set the knob at ”OFF” / "0" position, take out the plug from the mains socket.
Open the lid and remove the food from the freezer.
After about 0.5h, it is possible to remove the white frost or water from the smooth wall surfaces.
There is a water conduit at the bottom of the freezer, when defrosting, extract the rubber cover,
defrosted water will drip into the hole and ow out. (NOTES: PLEASE KEEP THE RUBBER COVER
WELL DURING THE DEFROSTING AND PUT IT BACK AFTER DEFROSTING IS DONE )
Extract the water conduit by 20-25mm until the water hole can be seen.
Twist the water conduit until the arrow points downward.
After defrosting is done, make sure there is no more water coming out before out the water conduit in
place and make the arrow point upward.
Wash the interior of the freezer and wipe it dry.
Switch on the appliance as per the relevant point in the manual.
EN
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Amica FS1003 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Amica FS1003 in the language / languages: English as an attachment in your email.

The manual is 1.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info