733755
13
Zoom out
Zoom in
Previous page
1/42
Next page
11
User’s manual
EN
SETTING UP OF THE PERIMETER WIRE
Before installing the perimeter wire, it is necessary to check the
entire surface of the lawn. Make any necessary adjustments to the
grassy surface during the laying of the perimeter wire in order to
allow the robot to function correctly.
1. Evaluate the best method for returning to the charging station
according to the instructions described in the chapter “RE-
ENTRY METHOD TO THE CHARGING STATION”.
2. Evaluate whether a special installation of the perimeter wire
is necessary according to the instructions described in the
chapter “SET-UP OF THE ROBOT’S QUICK RE-ENTRY TO
THE CHARGING STATION”.
3. Preparation and dening of the work areas.
4. Installation of the perimeter wire.
5. Installation of the charging station and power supply unit. When
laying the perimeter wire, respect the installation direction
(clockwise) and the rotation direction around the owerbeds
(counter-clockwise), As shown in the gure.
track for laying the perimeter wire
RE-ENTRY METHOD TO THE CHARGING STATION
The robot can return to the charging station in two different ways
based on what is set in the user menu under the eld “Settings
Re-entry to Base.” Use the “On the Wire” method only when there
are numerous obstacles inside the garden and near the perimeter
wire (within 2 meters). In all other cases it is better to use the
“V-Meter” method for the quickest re-entry to the charging station.
“Follow wire”. This method of re-entry to the charging station
commands the robot to follow the perimeter wire, positioning its
wheels on either side of the wire. If this method is activated, there
is no need to prepare the “Recall on Wire” as described below.
“V-Meter”. By setting this method of re-entry to the charging
station, the robot runs along the perimeter wire at an indicative
distance ranging from a few centimetres to one meter (3.2 '),
touching it every now and again in the curved sections until the
signal emitted by the charging station has been recognised for
guiding itself on the wire and entering correctly into the charging
station.
step
lower 2 mt.
5 cm.
2 mt.
2 mt.
2 mt.
10 mt. 1,5 mt.
charging
station
If narrow passages are present or the arrow for quick re-entry to the charging station, the wire must be positioned in a special
way, called “Recall on the wire.”
As soon as a “Recall” is recognised, the robot will follow the perimeter wire at low speed, and with more precision for around
10 meters (33 '). It will then return to the “V-Meter” re-entry mode if the quick re-entry or charging station was not encountered.
Follow these instructions to install the “Recall:
the “Recall” is a piece of wire that extends for around 2 m (6.6 ') with a distance of 5 cm (1.96 ") between each wire;
the “Recall” must be positioned at a distance of 2 m. (6.6 ') in front of any narrow passages;
the “Recall” must be positioned in the section in front of the “Quick Re-entry”.
NB: If the robot does not nd the charging station within a certain amount of time, it will follow the perimeter wire in
“Follow wire” mode.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ambrogio L85 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ambrogio L85 in the language / languages: English as an attachment in your email.

The manual is 5,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ambrogio L85

Ambrogio L85 User Manual - Dutch - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info