644612
4
Zoom out
Zoom in
Previous page
1/32
Next page
4
User’s manual
EN
skills, please disconnect power and activate the safety device. However, the user must take all necessary safety precautions,
in particular when working on the bottom of the lawnmower robot, following procedures indicated by the manufacturer.
•
Use the personal protection devices recommended by the Manufacturer, in particular, always wear protective gloves when
handling the cutting blade.
•
Before replacing the batteries, always remove the blade.
•
Make sure the air vents of the power supply unit are free and clear of residuals.
•
To avoid irreversible damage to the electric and electronic parts, do not wash the robot with water jets at a high pressure and
do not immerse it in water, partially or completely, as it is not watertight.
•
Operators who perform repairs during the working life of the robot must have the necessary technical expertise, skills and
experience in this specic eld. The lack of these requirements may be hazardous to the health and safety of people.
•
Inspect the robot at regular intervals to ensure that the blade, the assembly screws and the cutting mechanism are not worn
or damaged. Replace badly worn parts using original spare parts to ensure proper function and the required safety level.
•
Make sure that all nuts, bolts and screws are tightened to ensure that the robot is in good operating conditions.
•
The robot cannot be used without the top cover. If the mechanical parts of the robot are damaged, replace them.
•
Any routine or extraordinary maintenance (e.g. battery replacement) must be performed by an authorised service centre.
•
The Manufacturer shall not be held liable if non-original spare parts are used.
•
Never use and recharge the robot in explosive and/or ammable environments.
•
To recharge the robot, use only battery chargers and power supply units provided by the supplier. Improper use may cause
electric shocks, overheating or leakage of corrosive liquids from the battery. If any liquid leaks, the battery must be washed
with water / neutraliser; seek medical assistance for contact with the eyes.
SAFETY DEVICES
1. Bumpers
The bumper sensor is activated if the robot strikes a solid object greater than 9 cm (3.54 ") in height, which stops the movement
in that direction and moves backwards to avoid the obstacle.
2. Inclinometer
If the robot works on a slope which is steeper than the maximum limit, or tips over, the robot will stop the cutting blade.
3. Emergency stop switch
Located on the control panel with the word “STOP” larger than the other commands on the keypad. Pressing this button at any
time during operation will immediately stop the movement of the lawnmower robot and the rotation of the blade will stop within
2 seconds.
4. Over-current protection
Each motor (blade and wheels) is monitored continuously during operation for any situation that may cause them to overheat. If
this occurs in the wheel motor, the robot will attempt to move in the opposite direction. If the over-current persists, the robot will
stop and signal an error. If the cutting blade motor overheats, there are two intervention ranges. If the parameters fall within the
rst range, the robot will perform the manoeuvres to unblock the cutting blade. If the over-current is below the protection range,
the robot will stop and signal a motor error.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ambrogio L50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ambrogio L50 in the language / languages: English as an attachment in your email.

The manual is 9,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ambrogio L50

Ambrogio L50 User Manual - German - 23 pages

Ambrogio L50 User Manual - German - 18 pages

Ambrogio L50 Additional guide - Dutch - 3 pages

Ambrogio L50 Additional guide - Dutch - 2 pages

Ambrogio L50 User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info