733759
37
Zoom out
Zoom in
Previous page
1/42
Next page
35
User’s manual
EN
Problem Cause Remedies
The work area is not
completely mowed
Not enough work hours
Extend the working time (see “Programming
Mode”)
Cutting blade clogged with deposits
and/or residuals
Stop the robot safely (see “Robot Safety Stop”)
Warning – Caution
Use protective gloves to prevent injuries to
your hands.
Clean the cutting blade
Cutting blade worn out
Replace the blade with an original spare part
(see “Blade replacement”)
Work area too big compared to the
actual capacity of the robot
Adjust the work area (see “Technical
specications”)
The batteries are about to run out.
Replace the batteries with original spare parts
(see “Battery replacement”)
The batteries do not charge completely
Clean and remove any rust from the contact
points of the batteries (see “Robot Cleaning”).
Secondary area not
completely mowed
Programming error
Correctly program the secondary area (see
“Programming Mode”)
“Service” appears on the
display
The robot needs to be serviced Contact your nearest authorised service centre
“Lift” appears on the display The robot is lifted from the ground
Check that the robot is not blocked or obstructed
by any objects.
Clean and eliminate any residual grass under
the body shell which may obstruct the sensors
(see "Robot cleaning")
“No Signal” appears on the
display
The perimeter wire is not connected
correctly (broken cable, no electrical
connection, etc.)
Check the functioning of the electrical power
supply, the correct connection of the power
supply unit and of the charging station (see
“Installation of charging station and power supply
unit”)
“Out of border” appears on
the display
Too much slope
Delimit the area with too much slope (see
“Planning of system installation”)
Perimeter wire laid incorrectly
Check that the wire has been installed correctly
(too deep, next to metallic objects, distance
between the wire marking the two elements
less than 70 cm, etc.) (see “Planning of system
installation”)
Perimeter wire marking the boundary of
the inside areas (owerbeds, bushes,
etc.) laid in a counter-clockwise
direction
Reposition the perimeter wire correctly (counter-
clockwise direction) (see “Installation of
perimeter wire”)
Overheated power supply unit
Adopt the appropriate measures to reduce the
temperature of the power supply unit (ventilate
or modify the installation area, etc.) (see
“Planning of system installation”)
Incorrect wheel transmission
Check and, if necessary, correctly fasten the
wheels
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ambrogio L250i Elite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ambrogio L250i Elite in the language / languages: English as an attachment in your email.

The manual is 8,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ambrogio L250i Elite

Ambrogio L250i Elite User Manual - German - 42 pages

Ambrogio L250i Elite User Manual - Dutch - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info