733759
14
Zoom out
Zoom in
Previous page
1/42
Next page
12
User’s manual
EN
SETUP OF THE ROBOT’S QUICK RE-ENTRY TO THE CHARGING STATION
Quick re-entry requires a special installation of the perimeter wire that allows the robot to reduce the re-entry path to the charging
station. This special installation of the perimeter wire should only be used for gardens where quick re-entry signicantly reduces
the path and where the perimeter length is greater than 200 meters.
To setup the quick re-entry, position the perimeter wire on the ground so that it forms a triangle with one side of 50 cm (19.7 ")
and the other two sides of 40 cm (15.75 ") each, as shown in the gure.
As the robot heads back to the charging station with the two wheels on either side of the wire, it intercepts this triangle and stops
moving. It then turns approximately 90° towards the inside of the garden and starts moving in the new direction until running into
the perimeter wire on the opposite side.
Arrange the wire for quick re-entry in a point where there is at least 200 cm (78.74 ") of straight wire in front of the station, and at
least 150 cm (59.05 ") of straight wire behind it.
Do not set up the wire along the straight section immediately in front of the charging station or near any obstacles. Make sure
there are no obstacles along the re-entry path that may obstruct the quick re-entry.
Do not set up the wire along excessive slope, so that the robot can recognizes easy it.The maximum slope depends on the lawn
conditions. it should be remain under approximately 20%.
Important
An incorrect setup of the robot’s quick re-entry may prevent the robot from returning to the charging station
quickly. When the robot travels along the perimeter to reach a secondary area, it may not detect the quick
re-entry setup.
The illustration provides some useful tips on how to correctly setup
the robot for a quick re-entry.
40 40
50
1,5 mt.
step
lower
2 mt.
4-10 mt.
min. 150 cm.
10 mt.
5 cm.
2 mt.
2 mt.
2 mt.
charging
station
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ambrogio L250i Elite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ambrogio L250i Elite in the language / languages: English as an attachment in your email.

The manual is 8,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ambrogio L250i Elite

Ambrogio L250i Elite User Manual - German - 42 pages

Ambrogio L250i Elite User Manual - Dutch - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info