733758
30
Zoom out
Zoom in
Previous page
1/42
Next page
28
User’s manual
EN
INITIAL START UP – AUTOMATIC MODE
The automatic cycle is started during the initial start-up or after a period of inactivity.
1. Check that the height of the lawn surface to mow is compatible with the proper functioning of the robot (see “Technical
Specications”).
2. Adjust the cutting height as desired (see “Adjustment of Cutting Height).
3. Check that the work area has been correctly marked and that there are no impediments to the regular functioning of the robot
as indicated in the section “Preparation and Marking the Boundaries of the Work Areas” and following sections.
4. Position the robot inside the charging station.
5. Press the "ON/OFF" button and wait a few seconds for the robot to turn on completely. Follow the instructions on the display
and enter the password if prompted.
6. If starting the robot for the rst time, it is necessary to program the settings. However, if starting the robot after a long period
of inactivity, check that the programmed functions correspond to the actual condition of the lawn to be mowed (e.g. addition
of a pool, plants, etc.) (See “Programming Mode”).
7. After a few seconds, the message “CHARGING” will appear on the display.
8. The robot starts to mow the lawn according to the modes programmed.
9. Check there are no large puddles after a heavy rain, otherwise the area must be put in order or make sure the robot is in
"Pause".
ROBOT SAFETY STOP
During use, it may be necessary to stop the robot. In normal conditions, the robot can be stopped with the “STOP” key. In case
of danger or when performing any maintenance, it is necessary to stop the robot in safe conditions in order to prevent the blade
from accidently starting. First press the “STOP” button and then the "ON/OFF " button. Disconnect the power plug from the
electrical outlet.
Important
The robot safety stop is necessary during
maintenance and repairs (for example, blade
replacement, cleaning operations, etc.).
To start, proceed as indicated:
-
position the robot inside the cutting area;
-
press the "ON/OFF" button to turn on the robot and run the
start-up procedure again.
If the robot is started up outside of the cutting area, the blade
motor will not start and after briey searching for the signal, the
robot will show "OUT OF BORDER" on the display. Press "ON/
OFF", position the robot inside the cutting area and carry out the
start up procedure again.
ON/OFF
STOP
.....................................
......................
10:30
AUTOMATIC RETURN TO THE CHARGING STATION
The robot stops the work cycle if the following conditions are veried:
-
End of working time: at the end of the working time, the robot automatically returns to the charging station and starts
operating again according to what has been programmed (see “Programming Mode”).
-
Rain: with the function active, the robot returns to the recharging station automatically and will start working again as
programmed (see "Programming mode").
-
Battery to be charged: the robot automatically returns to the charging station.
-
Eco Mode: if the sensor detects that the lawn has already been mowed, it automatically returns to the charging station and
starts operating again according to what has been programmed (see “Programming Mode”).
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ambrogio L250 Deluxe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ambrogio L250 Deluxe in the language / languages: English as an attachment in your email.

The manual is 8,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ambrogio L250 Deluxe

Ambrogio L250 Deluxe User Manual - German - 42 pages

Ambrogio L250 Deluxe User Manual - Dutch - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info