337705

Amana gb 2026 d rvs Manual

5
Zoom out
Zoom in
Previous page
1/288
Next page
For pullout drawer only:
1. Turn both stabilizing
legs clockwise until
firmly against floor.
Turn roller
adjustment screws 2
to 3 times counterclockwise so that the full
weight of refrigerator rests on stabilizing legs.
2. Replace toe grille. See markings on inside of toe
grille to insure proper placement.
Roller Adjustment Screw
Stabilizing
Leg
4
Installation
CC
A
B
A
B
4. Using the carpenter’s level, make sure front of
refrigerator is 6 mm or approximately one half
bubble higher than back of refrigerator and that
the refrigerator is level from side to side.
5. Turn stabilizing legs (C) clockwise until firmly
against floor.
6. Freezer drawer models only: Turn adjustment
screws (A) counterclockwise to allow the full
weight of the refrigerator to rest on the
stabilizing legs.
7. Replace the toe grille.
• Align the toe grille mounting clips with the lower
cabinet slots.
• Snap bottom portion into place first. Press
down on top of grille until top portion snaps into
place.
2. Using hex head driver, turn the front adjustment
screws (A) on each side to raise or lower the front
of the refrigerator.
Handles
If not installed, the handle is located in the interior of
the fresh food section or attached to the back of your
refrigerator.
Remove and discard handle packaging and tape.
Handle design varies from refrigerator to refrigerator.
Please reference the appropriate instructions for your
model below.
3. Select models also have rear adjustment screws
(B). Using the hex head driver, turn each of these
adjustment screws (B) to raise or lower the rear of
the refrigerator.
Fresh Food Handles
Front Mount Handle - Style 1
Materials Needed:
• Phillips screwdriver
•
5
⁄16” hex head driver
To Install:
1. Remove 0.6 cm hex head screws from
door face with hex head driver, and
Phillips screw from top of door.
• If reversing door, remove door plugs
from opposite side of door and
insert in screw holes.
2. Align handle holes with screw holes on
door face and secure with two door face
screws from step 1.
3. Locate handle trim in literature pack and
install over top and bottom of handle, as
illustrated.
• Secure top handle trim with remaining
screw removed in step 1.
• Snap bottom trim over bottom portion
of handle.
To Remove:
1. Remove top handle trim by removing top
handle screw.
• Retain trim and screw for later
replacement.
2. Pry bottom handle trim from handle with
screwdriver flat blade wrapped in
masking tape.
• Retain trim for later replacement.
3. Remove two hex head screws.
• Retain screws for later replacement.
Side Mount Handle
Materials Needed:
• Phillips screwdriver
To Install:
1. Remove screws from the side of the door.
2. Align the side mount handle with the pre-drilled
holes in the door panel.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Amana gb 2026 d rvs at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Amana gb 2026 d rvs in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info