541725
11
Zoom out
Zoom in
Previous page
1/14
Next page
7. TECHNICAL SPECIFICATIONS
7.1 Specifications
ELECTRICAL SPECIFICATIONS
INPUT SENSITIVITY
INPUT IMPEDANCE
FREQUENCY RESPONSE
(at 10dB below rated output power)
VOLTAGE GAIN
DISTORTION(SMPTE-1M)
S/N ratio
Full short circuit, open circuit, thermal, ultrasonic, and RF protection stable into reactive
or mismatched loads, turn ON/OFF, muting, tried crowbar.
GENERAL SPECIFICATIONS
PROTECTIONS
CONTROLS
INDICATORS
CONNECTORS
POWER SUPPLY
DIMENSIONS
WEIGHT
Front: AC switch 40-detect input level control for
Rear: stereo/ parallel/ bridged selector, 30Hz filter selector clip ON/OFF selector.
each channel.
SIGNAL: 2×green LED
CLIP: 2×red LED
POWER: 1 green LED
INPUT : Active balanced XLR and 1/4"(6.3mm)TRS
OUTPUT: "Touch-proof" binding posts and speak-on jacks.
Available for 110-120V or 220~240V AC, 50/60Hz
483(W)×400(D)×88.8(H)mm
13.6kg 15.6kg 19kg
600W
600W
900W
900W
1500W
1500W
1.15V(+3.4dBu)
10KΩ Unbalanced 20KΩ Balanced
25Hz~25KHz +0/-1dB
-3dB points: 5Hz~50KHz
1.15V(+3.4dBu)
30dB
<0.03%
32dB 34dB
<0.03% <0.03%
100dB 100dB 100dB
1.15V(+3.4dBu)
4 Ohms
4 Ohms
2 Ohms
8 Ohms
8 Ohms
POWER SPECIFICATIONS
MACRO830
480
300
205
560
800
800
450
310
900
1400
MACRO1400
MACRO2400
1400
750
575
1500
2500
STEREO MODE
(Both channels driven)
20Hz~20KHz
Bridge Mono Mode
20Hz~20kHz
PROTECTION: 1 red LED
As to the speaker cable, if you use a long one, use as thick a cable as possible to prevent deterioration of the
damping factor or power loss inside the cable.
Use the following formula to determine the fuse capacity according to the speaker's input capacity.
2
Po=I R I=Po/R
Po[W] : Speaker's continuous input capacity (noise or RMS)
R[Ω] : Speaker's nominal impedance
I[A] : Required fuse capacity
6.2 Caution for Speaker Connection
The output capacity of out MACRO 830/1400/2400 Professional Stereo Amplifier is very high, be sure to use a speaker
system that has sufficient input capacity. If the input capacity of your speaker system is lower than the rated output of
the MACRO 830/1400/2400 Professional Stereo Amplifier, you can protect your speakers by connecting a fuse serially
between the speaker and the amplifier as shown below.
10
Output
Fuse
(+)
(-)
+
-
Speaker
System
PROFESSIONAL HIGH POWER STEREO AMPLIFIER
CH-A CH-B
CLIP
SIG
POW ER
ON
OFF
CLIP
SIG
PROT
MACRO2400
CH-A CH-B
CLIP
SIG
POW ER
ON
OFF
CLIP
SIG
PROT
LTO
RR
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alto Professional MACRO 2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alto Professional MACRO 2400 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info