541754
4
Zoom out
Zoom in
Previous page
1/20
Next page
4
REAR PANEL
1
2
3
3
54
7
8
8
8
8
8
8
8
8
9
9
11
10
6
3
3
1. POWER INPUT – Connect the included power cable to this input and connect the other
end of the cable to a power source. Make sure the top panel's POWER SWITCH is set to
"off" when plugging and unplugging the cable.
2. COOLING FAN – Keep the area in front of this vent clear from obstructions. The fan
behind the vent cools the amplifier, preventing overheating.
3. MIX OUT – Use standard balanced XLR cables
or balanced 1/4" mono TRS cables to connect
these outputs to the inputs of your active
loudspeakers.
4. SUB OUT – Use a standard balanced 1/4"
mono TRS cable to connect this output to the
input of an optional powered subwoofer.
5. LINK OUT – Use a standard unbalanced 1/4"
stereo TRS cable to connect this output to the
LINK IN of an optional second Kick amplifier (sold separately). When using this output, this
amplifier will be the "master"; it controls the audio, volume, etc. sent to the "slave" amplifier
connected to this output (each amplifier will output the same signal in parallel).
Alternatively, you may use a 1/4" stereo TRS splitter cable to connect this output to two
separate loudspeakers (left and right), two channels (left and right) of an external mixer,
etc.
6. LINK IN – Use a standard unbalanced 1/4" stereo TRS cable to connect this input to the
LINK OUT of an optional second Kick amplifier (sold separately). When using this input,
this amplifier will be the "slave"; its levels will be controlled by the "master" amplifier
connected to this input (each amplifier will output a summed mono signal).
7. MIC IN – Use a standard XLR cable to connect a microphone to this input.
8. LINE IN – Use standard 1/4" TRS cables to connect line-level instruments or sound
sources to these inputs. When connecting a mono sound source, use only the "L/MONO"
input.
9. AUX IN – Use a standard stereo RCA cable to connect a line-level sound source to these
inputs.
10. FOOT SW – You can connect a standard 1/4" TRS latching footswitch (sold separately) to
this input. A connected footswitch will allow you to activate/deactivate the amplifier's built-
in effects processor.
11. GROUND SWITCH – Depressing this switch grounds the amplifier, which can reduce hum
or noise.
Tip
(left channel)
Ring
(right channel)
Sleeve
(ground)
TRS connector
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alto Professional Kick 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alto Professional Kick 15 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info