541740

Alto Professional Black 15 sub Manual

7
Zoom out
Zoom in
Previous page
1/36
Next page
7
Features
Rear Panel
1. Power Input: Use the included IEC power cable
to connect this input to a power source.
2. Fuse: If the unit's fuse is broken, lift this tab to
replace the fuse. Replace it with a fuse with an
appropriate rating (printed under the unit's power
cable input). Using a fuse with an incorrect rating
can damage the unit and/or fuse.
3. Power Switch: Use this switch to power the
subwoofer on or off.
4. Power/Standby LED: This LED illuminates when
the subwoofer is powered on.
5. Standby On/Off Switch: By default, this
subwoofer has its Standby Mode enabled: when
no incoming audio signal is detected for
approximately 15 minutes, the subwoofer will
enter a low-power state. The subwoofer will exit
Standby Mode within 0.5 seconds of detecting an
incoming audio signal. Change this recessed
switch's setting to the Off position to disable this
feature.
6. Logo On/Off Switch: Press this to turn the light
in the Alto Professional logo on or off.
7. Polarity Switch and LED: Press this switch to toggle the polarity of the subwoofer's acoustic output. In
some cases, reversing the polarity can help reduce any interference in the frequency overlap between
the subwoofer and main loudspeaker. When the LED is off, the subwoofer is set to its default positive
polarity (the recommended setting when used with Black Series loudspeakers). When the LED
illuminates red, the subwoofer's polarity is reversed from its default.
Important: When using multiple Black Series subwoofers, make sure they are set to the same polarity
to avoid cancellation of the bass frequencies.
8. Inputs: Use a standard XLR or 1/4" (6.35 mm) cable to connect your audio source to this input. This
input accepts both line-level sources only.
9. Input Volume Knob: Use this knob to set the level of the audio going into the inputs. The Black 15sub
is engineered to work seamlessly together with Black 10, Black 12, or Black 15 loudspeaker models.
For optimal bass balance, set the Black 15sub input volume knob to the 12 o’clock-position detent, and
set the Black 10, Black 12, or Black 15 volume knobs to their maximum clockwise position. Adjust the
volume controls as needed to further fine-tune the audio level from each system.
10. Signal/Limit LED: This LED illuminates green when an incoming audio signal is detected. It
illuminates red when the audio signal level is too high and is being dynamically reduced to protect the
subwoofer from damage or distortion. If this LED is continually illuminated red, or if the audio output
sounds excessively distorted, then reduce the volume of the connected audio source, or reduce the
setting of the Input Volume Knob.
11.
Outputs: Use a standard XLR cable to connect this balanced output to the input of a Black Series
loudspeaker. Audio is sent from this output at 0 dB.
12. Crossover Bypass Switch and LED: Press this switch to toggle between Standard and Bypass
Modes. When the LED is off, the subwoofer is in Standard Mode (the default) where the XLR outputs'
signal is high-pass-filtered to be sent to a full-range loudspeaker. When the LED illuminates green, the
subwoofer is in Bypass Mode where the XLR outputs' signal will be unfiltered and full-range (the XLR
outputs effectively function as loop-through connectors in this case).
13. Ground Switch: Engage (depress) this switch to reduce hum or noise.
14. DSP Mode Button: Press this button to cycle through the subwoofer's internal low-pass crossover
DSP settings, as shown on the rear panel. The LED next to the setting will illuminate when selected.
For most applications, we recommend using the 80 Hz or 100 Hz setting; use the 120 Hz or 140 Hz
settings to increase mid-bass impact.
15. Pairing Button and LED: Press and release this button to pair the subwoofer to your iPad or iPhone.
The Pairing LED will illuminate when it is paired. See the Bluetooth Pairing section for instructions.
2
4
1
5
6
7
8
10
11
14
13
12
9
3
15
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alto Professional Black 15 sub at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alto Professional Black 15 sub in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info