586744
8
Zoom out
Zoom in
Previous page
1/11
Next page
15
7.0 Trouble shooting guide EN
To avoid unnecessary disappointments, you should check the following before contacting the ALTO service
organisation:
Symptom Cause Recommended action
Machine refuses to start Machine not plugged in Plug in machine.
Defective socket Try another socket.
Fuse has blown Replace fuse. Switch off other machines.
Defective extension cable Try without the ex ten sion cable.
Fluctuating pressure Pump sucking air Check that hoses and connections are air
tight.
Valves dirty, worn out Clean and replace or refer to local ALTO
or stuck distributor
Pump seals worn out Clean and replace or refer to local ALTO
distributor.
Motor busses Low voltage or Activate the trigger of the spray handle.
low temperature
Machine stops Fuse has blown Replace fuse. Switch off other machines.
Incorrect mains voltage Check that the mains voltage corresponds to
specifi cation on the model tag.
Thermal sensor activated Leave the washer for 5 minutes to cool down.
Nozzle partially blocked Clean the nozzle (see section 4.1)
Fuse blows Fuse too small Change to an installation higher than the
amp. consumption of the ma chine.
You may try without the extension cable.
Machine pulsating Air in inlet hose/pump Allow machine to run with open trigger until
regular working pressure resumes.
Inadequate supply of Check that the water supply corresponds to
mains water specifi cations required (see model tag)
NB! Avoid using long, thin hoses (min 1/2")
Nozzle partially blocked Clean the nozzle (see section 4.1)
Water fi lter blocked Clean the fi lter (see section 4.2)
Hose kinked Straighten out hose.
Machine often starts Pump/spray handle is Contact your nearest ALTO Service Centre.
and stops by itself leaking
Machine starts, but Pump/hoses or accessory Wait for pump/hoses or accessory to thaw.
no water comes out frozen
No water supply Connect inlet water.
Water fi lter blocked Clean the fi lter (see section 4.2)
Nozzle blocked Clean the nozzle (see section 4.1)
Machine refuses to Start/stop valve stuck Turn off the water supply.
restart Relieve the spray handle.
In case problems other than the above occur, please contact your local ALTO distributor.
Customer services (UK only): ALTO Cleaning Sys tems Ltd. Phone: 01 768 868 995
Gilwilly In dus tri al Estate
Penrith, Cumbria CA11 9BN
Customer services (AUS) ALTO Overseas Inc. Phone: 02 9524 6122
1B/8 Resolution Drive
P.O. Box 797
Caringbah, N.S.W. 2229
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alto COMPACT 1050 X-TRA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alto COMPACT 1050 X-TRA in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alto COMPACT 1050 X-TRA

Alto COMPACT 1050 X-TRA User Manual - German - 11 pages

Alto COMPACT 1050 X-TRA User Manual - Dutch - 11 pages

Alto COMPACT 1050 X-TRA User Manual - French - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info