471337
7
Zoom out
Zoom in
Previous page
1/12
Next page
Page 7
Installation
Caution:
Do not install the monitor near the front passenger seat air bag system.
<Mount it using the supplied bracket>
1. Assemble the supplied bracket and mount the monitor temporarily.
Note: Always use the supplied bracket or equivalent.
2. Verify the installation location.
Select a flat surface and temporarily mount the unit. Use adhesive
tape, etc.
Notes:
• Mounting hints
• Top of the monitor should not exceed the top of the dash when
viewed from the driver’s seat.
• Use a stable mounting surface.
Angle the monitor for easy viewing.
• In a vehicle with a front passenger air bag, do not install the unit
where it will interfere with the operation of the safety systems.
• If the surface of the dash board is finished with other than plastic
(leather, wooden panel, cloth covered panel, etc.), there will be
some damage if the bracket is removed.
• Installation close to other equipment (such as a GPS antenna) may
give rise to mutual interference. Please pay careful attention to the
installation location and maintain sufficient space between other
equipment.
3. Remove the monitor from the bracket.
4. Peel the protective paper from the double-stick tape on the bracket’s
base.
Clean the mounting location with a suitable cleaner.
Notes:
Warm the mounting location with a dryer, etc. and then place the
bracket into position.
Do not apply force or moisture for 24 hours after installation.
If the bracket is not attached securely with just the tape, use the
supplied screws to complete the installation.
If the mounted surface is curved slightly, reform the base to fit to its
shape.
5. Mount the monitor to the bracket.
Thread the mounting screw into hole at the bottom of the monitor.
Secure the monitor by tightening the screw. Depending upon the
location, the bracket can also be mounted using the supplied nut to
slide into the back of the monitor. Thread the bracket mounting screw
into the nut. Slide the nut in the channel on the back of the monitor
and adjust the height and tighten.
Dress the monitor’s cable using the cord clamp provided.
6. Adjust the height and angle of the monitor for easy visibility.
Determine the height and angle. Tighten the height and angle
adjusting screws to secure the monitor.
NOTE:
The A/V Interface box may be mounted in any suitable location. Make sure the box and the wires
connected to it will not interfere with safely operating the vehicle.
Mounting the Interface box near the monitor will reduce the need for additional cable extensions.
This monitor can be mounted in a headrest if desired. A special mounting kit is required and can be
purchased from your Authorized Alpine dealer. Ask for model KTE-580V.
1
2
5
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine TME-M580 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine TME-M580 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info