471407
64
Zoom out
Zoom in
Previous page
1/67
Next page
62-EN
01GB08PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
In Case of Difficulty
If you encounter a problem, please turn the power off, then on again. If
the unit is still not functioning normally, please review the items in the
following checklist. This guide will help you isolate the problem if the
unit is at fault. Otherwise, make sure the rest of your system is properly
connected or consult your authorized Alpine dealer.
No function or display.
Vehicle’s ignition is off.
- Turn the ignition key on. If connected as per the instructions,
the unit will not operate with the vehicles ignition off.
Unit’s power is not on.
- Turn the ignition key on. Press one of the switches on the
Commander to turn power on. If an Ai-NET compatible head
unit is connected, turn on the power by the head unit.
Power cord connection is faulty.
- Connect the power cord correctly.
Display does not show anything (BLACK OUT function).
- Cancel BLACK OUT function (see page 57).
•Blown fuse.
- Check the fuse of the unit; replace with the proper value if
necessary.
Internal micro-computer malfunctioned due to interference noise
etc.
- Press the RESET switch with a ball-point pen or other pointed
article.
Power is on but no sound is coming out.
Volume level is at Minimum.
- Raise the volume level (see pages 12, 36).
External input system does not match the setup.
- Set the system so that it matches the connected input (see
pages 14, 39).
The sound is not output from the speakers.
Cord connection is faulty.
- Connect the cord correctly.
Speaker is in "OFF mode."
- Put the speakers in "ON mode" (see pages 14, 38).
Subwoofers are "OFF."
- Turn the subwoofers "ON" (see pages 14, 38).
Sound adjustment disabled.
Defeat is "ON."
- Turn Defeat Off (see pages 12, 36).
DVD volume low.
Volume levels can be different between CD and DVD.
- Adjust the DVD Level (see pages 34, 57).
Sources cannot be selected.
Ai-NET device is connected.
- When an Ai-NET compatible head unit is connected, the
source should be switched at the head unit.
Dolby Pro Logic II volume level low.
Dolby Pro Logic II volume level is generally lower.
- Raise the volume level (see pages 12, 36).
Dolby D/Dolby PLII/DTS indicators flash at 1 second
intervals simultaneously.
Software upgrade to a newer version failed.
- Consult your Alpine dealer.
POWER indicator flashes at 1 second intervals.
A failure has occurred.
- Following the instruction on the screen, conduct the corrective
measures. Or, consult your Alpine dealer.
RoadEQ does not work.
Microphone not connected.
- Check to see that the microphone is correctly connected. Also,
make sure that the cord is not extremely bent.
RoadEQ setup not completed.
- Check to see that RoadEQ is correctly completed.
An error during Automatic ImprintEQ adjustment has
occured.
External noise is interfering with measurement.
- Conduct the measurement in a quiet location.
The speaker bandwidth may be too narrow.
- Check the X-Over setting of each speaker.
Gain setting of the amplifier may be too low.
- Check the Gain setting.
Software upgrade to a newer version failed.
During software upgrade, the USB cable was unplugged, the
ignition key is turned to OFF position, the unit was affected by
another program, etc.
- Stop all active programs, and then upgrade the software again
(see page 11).
- If you still have trouble, stop use of the unit and consult your
Alpine dealer.
Automatic measurement failed for whatever reason.
- Press "Rotary Encoder" to go back to the previous screen and
perform the measurement again.
Microphone not connected.
- Check to see that the microphone is correctly connected. Also,
make sure that the cord is not extremely bent.
Even when RoadEQ is turned on, if no microphone is connected,
RoadEQ is turned off.
- Check to see that the microphone is correctly connected. Also,
make sure that the cord is not extremely bent.
Settings are called but there is no preset data stored in the
system.
- Store the preset values.
The called preset values do not match the current speaker
system.
- Store the preset values again, using the current speaker system.
Indication (Commander RUX-C800)
Calibration Error
No Mic
No Mic/RoadEQ Off
No Data
System Mismatch
01GB00PXAH800.book Page 62 Tuesday, February 8, 2011 9:04 PM
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine RUX-C800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine RUX-C800 in the language / languages: English as an attachment in your email.

The manual is 11,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info