471407
45
Zoom out
Zoom in
Previous page
1/67
Next page
43-EN
01GB07PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From the Commander
6
Rotate the [Rotary encoder] to select “Auto TCR,
and then press the [Rotary encoder].
The AUTO TCR screen is displayed.
7
Press the [Rotary encoder].
Countdown will start.
During the 10 second countdown, go outside the vehicle
and close the door.
A test signal will be output from the speakers to measure the
acoustic characteristics of the cabin. Do not open any
doors until the screen indicates “Finished.” If external noise
interferes with the measurement, the “Calibration Error”
message will appear on the screen. In this case, click
[Rotary encoder] again to re-measure.
If you want to stop measurement, press [ ].
If the microphone is not connected, “No Mic” will be displayed and
the measurement will not be carried out. Press [ ] or [Rotary
Encoder] to cancel the indication.
8
When “Finished” appears, press [Rotary encoder].
This function is not available when Defeat is set to ON.
Measurement of Auto TCR takes approximately 5 minutes.
Auto TCR measurement result overwrites the manual TCR
measurement result.
Sound may arrive at the listening position at slightly different times,
depending on the speaker and enclosure. To compensate for this, the
distance can be adjusted to be larger than the actual distance.
After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 36).
Adjusting for Road Noise (RoadEQ)
RoadEQ (REAL-TIME OPTIMIZED ADAPTIVE DRIVING EQ) is a
function to automatically adjust the EQ properties in accordance with
the road noise while driving.
The Road Equalizer compensates for constantly changing noise, so
always keep the microphones connected.
1
Preparing for measurement.
Park the vehicle in a quiet location.
Close doors, windows, sunroof, etc.
Turn the air-conditioner and heater OFF.
Turn off the engine of the vehicle.
2
Preparing the microphone.
Refer to the installation manual.
3
Turn the ignition switch of the vehicle to ACC (On).
If an air-conditioner or heater is turned on, turn it off. Measurement
should not be performed if air-conditioner or heater noise is present.
4
Press [FUNC.].
5
Rotate the [Rotary encoder] to select “RoadEQ,” and
then press the [Rotary encoder].
6
Rotate the [Rotary encoder] to select “Calibration,
and then press the [Rotary encoder].
The CALIBRATION screen is displayed.
7
Press the [Rotary encoder].
Countdown will start.
During the 10 second countdown, go outside the vehicle
and close the door.
A test signal will be output from the speakers to measure the
acoustic characteristics of the cabin. Do not open any
doors until the screen indicates “Finished.” If external noise
interferes with the measurement, the “Calibration Error”
message will appear on the screen. In this case, click
[Rotary encoder] again to re-measure.
If you want to stop measurement, press [ ].
If the microphone is not connected, “No Mic” will be displayed and
the measurement will not be carried out. Press [ ] or [Rotary
Encoder] to cancel the indication.
8
When “Finished” appears, press [Rotary encoder].
This function is not available when Defeat is set to ON.
Measurement of RoadEQ takes approximately 7 minutes.
When you select “Calibration” again, the previous setup data will be
erased when count-down is started.
Measurement values will not be lost in the event the system is reset or
battery power is disconnected.
When automatic measurement is completed, RoadEQ can be turned on
or off and its level can be selected.
1
Press [FUNC.].
2
Rotate the [Rotary encoder] to select “Road EQ,
and then press the [Rotary encoder].
3
Rotate the [Rotary encoder] to select “Level
Adjustment,” and then press the [Rotary encoder].
The LEVEL ADJUSTMENT screen is displayed.
Turning RoadEQ On/Off
01GB00PXAH800.book Page 43 Tuesday, February 8, 2011 9:04 PM
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine RUX-C800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine RUX-C800 in the language / languages: English as an attachment in your email.

The manual is 11,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info