471407
23
Zoom out
Zoom in
Previous page
1/67
Next page
21-EN
01GB06PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From a PC
5
Click [Setup] for “RoadEQ.
6
When a confirmation message is displayed, check
the content and click [OK].
7
Click [START] in the measurement start screen.
Countdown will start.
During the 10 second countdown, go outside the vehicle
and close the door.
A test signal will be output from the speakers to measure the
acoustic characteristics of the cabin. Do not open any
doors until the finish message appears on the screen. If
external noise interferes with the measurement. If the error
screen is displayed, perform the measurement again.
If you want to stop measurement, click [CANCEL].
If no microphone is connected, a confirmation message will be
displayed and measurement will not be carried out. Click [OK] to
cancel the indication.
8
When a confirmation message for closing the screen
is displayed, click [OK].
To enable this function, Defeat should be is set to ON.
Measurement of RoadEQ takes approximately 7 minutes.
Measurement values will not be lost in the event the system is reset or
battery power is disconnected.
When automatic measurement is completed, RoadEQ can be turned on
or off and its level can be selected.
1
Click [RoadEQ] for [Shortcut] tab in the main menu.
The Automatic Measurement tab screen will be displayed.
When you click [Automatic Measurement] in the Function switching
tab, the Automatic Measurement tab screen will also be displayed.
Refer to “Operating the Function Switching Tab” (page 7).
2
Click [ON] or [OFF] for “RoadEQ.
When you click [ON], select the level.
When you do not use RoadEQ, select [OFF].
3
Click [ ] and select and click either [Level 1], [Level
2], or [Level 3].
Level 1: Low correction level. Suitable for quiet vehicles.
Level 2: Moderate correction level.
Level 3: High correction level. Suitable for high speed
driving.
If measurement is not completed, or a microphone is not connected,
this setting cannot be performed.
When you change the speaker setting of On/Off, RoadEQ
automatically becomes off. When you have changed the speaker
settings, start the measurement step over again.
After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 12).
Turning RoadEQ On/Off
01GB00PXAH800.book Page 21 Tuesday, February 8, 2011 9:04 PM
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine RUX-C800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine RUX-C800 in the language / languages: English as an attachment in your email.

The manual is 11,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info