471407
18
Zoom out
Zoom in
Previous page
1/67
Next page
16-EN
01GB06PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From a PC
When you connect an external input source, you can name it with a
suitable name (Initial setting: “Auxiliary”).
1
Click [ ] for each AUX and select and click the
external input product name from the pull-down
menu.
Setting item: AUX Name
Setting contents: Auxiliary/TV/EXT.DVD/Portable/Game
This item becomes possible to set only when AUX IN setting is on.
Setting/Adjusting the Navigation
Guidance Volume (Navi Mix)
If a navigation system is connected, its voice guidance will be mixed
with the system and output from the front speakers (Initial setting:
“OFF”). You can adjust the navigation guidance volume (Initial setting:
“0 dB”).
1
Click [ON] or [OFF] for “Navi Mix” in the main menu.
If you click [ON], select the setting value.
2
Click [ ] or [ ] to adjust the volume.
Setting contents: -10 to +10 dB
For details on the connection of a navigation system, refer to the
installation manual.
Before Performing Automatic
Measurement
This unit is equipped with ImprintEQ, RoadEQ, and AutoTCR
automatic measurement functions.
Be sure to read before performing automatic
measurement.
The automatic measurement should be performed in a quiet place
with the engine, air-conditioner, and heater turned off. If a mobile
phone or car phone is installed in the vehicle, move them outside of
the cabin, or turn the power off. Sound other than the measuring
sound (ambient noise around the vehicle, engine noise, and
ringtones) may interfere with measurement, resulting in inaccurate
measurement of the acoustic characteristics of the cabin.
Be aware that the battery may be drained if you use the unit for an
extended period of time without running the engine.
The microphone supplied with this product is specifically designed
for this type of measurement. Use of any other microphone will give
poor or no results. Use of microphones other than the one supplied is
not recommended.
If the system is equipped with a power amplifier with input level
control or a powered subwoofer, the measurement may not be
possible if the input level is set low. However, to perform correct
measurement, the input level should not be set too high.
For a power amplifier with low-pass filter, turn off the low-pass filter
of the power amplifier to make measurement. The low-pass filter in
the powered subwoofer or the power amplifier for a subwoofer
should be set at the highest cutoff frequency.
Measurement sequence for the automatic measurement
functions
Perform the automatic measurement in the following sequence.
When ImprintEQ is used:
First, ImprintEQ, then RoadEQ.
When ImprintEQ is not used:
First, Auto TCR, then RoadEQ.
When ImprintEQ is used, AutoTCR is not required.
When ImprintEQ and AutoTCR are performed after RoadEQ, re-
perform RoadEQ.
Naming the AUX Input (AUX Name)
Automatic
Measurement
Function
WARNING
Do not perform automatic measurement while the vehicle is
running.
Automatic measurement requires microphones to be installed
in the cabin to measure acoustic characteristics, and the
speakers may output loud noise for measurement. This may
interfere with safe driving and lead to an accident.
01GB00PXAH800.book Page 16 Tuesday, February 8, 2011 9:04 PM
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine RUX-C800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine RUX-C800 in the language / languages: English as an attachment in your email.

The manual is 11,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info