66420
7
Zoom out
Zoom in
Previous page
1/52
Next page
5-EN
EN
FR
ES
DE
SE
IT
Adjusting the input level
Using the analog, RCA-type connections, the
PXA-H701s input level must be preset from the
head unit.
Adjust the input level using a sound source with
a high recording level (such as pop or rock
music).
1 Turn on the head units power.
2 Turn the Rotary encoder on the main unit
counterclockwise and set the volume level to 0.
3 Gradually increase the volume of the head unit
until INPUT LEVEL OVER appears in the
display.
Reduce the volume slightly from this position,
until INPUT LEVEL OVER display just turns off.
This completes the setting.
Do not change the head unit volume level from
this optimum setting. Use the PXA-H701, only,
for changing the volume level.
NOTE
Switch to the spectrum analyzer display mode or the
input channel display mode before adjusting the input
level. (See page 29)
Adjusting the volume, balance, fader and subwoofer
After determining the input level, adjust the
volume, balance, fader and subwoofer from the
PXA-H701. Be careful not to make these
adjustments on the head unit.
1 Press the ENTER button and select the mode to
be adjusted.
2 Turn the Rotary encoder within 5 seconds and
adjust to the desired level.
VOLUME : 0 ~ 35
BALANCE : L15 ~ R15
FADER : F15 ~ R15
Sub.W LEVEL : 0 ~ +15
NOTE
When the subwoofer is set to OFF, the Sub.W
LEVEL adjustment is ineffective.
Using with RCA-type or optical cable
connections (non Ai-NET connections)
(only when using the control unit sold
separately)
Switching the input
The PXA-H701 is equipped with three sets of
analog signal inputs and three sets of digital
signal inputs. For further information about
connections, see Page 36.
1 Press the SETUP button.
The setup mode is set.
2 Turn the Rotary encoder to select the INPUT
SELECT mode, then press the ENTER button.
3 Turn the Rotary encoder to select the input
mode, then press the ENTER button.
4 Press the SETUP button repeatedly to quit the
setup mode.
NOTE
Non Ai-NET connections
Alpine products are equipped for a bus connection
system called Ai-NET which can only be used for
connections between Ai-NET products.
The PXA-H701 is an Ai-NET product, but is designed to
allow connections to other (non Ai-NET) products as
well. Thus RCA-type and optical cable connections are
also possible.
Connections to non Ai-NET products are referred to as
non Ai-NET connections.
Analog 1 Analog 2 Analog 3
Digital 3 Digital 2 Digital 1
VOLUME FADERBALANCE
Sub.W LEVEL
Using with Ai-NET connections
When Ai-NET connections are used, the volume,
subwoofer, balance and fader are adjusted from
the head unit (they cannot be adjusted from the
PXA-H701). However, BASS and TREB can not
be adjusted from the head unit, so adjust them
from PXA-H701.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine PXA-H701 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine PXA-H701 in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info