471424

Alpine MRX-M50 Manual

10
Zoom out
Zoom in
Previous page
1/20
Next page
English Français Español
ALPINE MRX-M100/MRX-M50 68-13530Z78-A (EN/FR/ES)
10
2. Remove the insulation from the ends of the wire leads by about
7 – 10mm (9/32” – 3/8”). (Fig. 5)
NOTES:
If length of the exposed wire is too short, a poor connection
may occur causing operation failure or sound interruption.
On the other hand, if the length is too long, an electrical
short-circuit may occur.
3. Tighten the set screw with the hexagon wrench (included) to
secure the lead. (Fig. 6)
Before making this connection, use insulated shrink
tubing to cover any exposed wire extending beyond the
terminal.
NOTES:
Use only the screws included.
For safety reasons, connect the battery leads last.
To prevent disconnection of the leads or dropping of the unit,
do not use the cabling to carry the unit.
•
•
•
•
•
2. Retirer l’isolation des bouts des fils de connexion de 7 – 10mm
(9/32” – 3/8”). (Fig. 5)
REMARQUES :
Si la longueur des conducteurs avec l’isolation retirée est
trop courte, une connexion incorrecte risque de se produire
et cela peut provoquer une panne de fonctionnement ou
l’interruption du son.
D’autre part, si la longueur du conducteur est trop longue, un
court-circuit électrique risque de se produire.
3. Serrez la vis avec une clé hexagonale (fournie) pour fixer le fil.
(Fig. 6)
Avant de faire cette connexion, utiliser la gaine
rétrécissable isolante afin de couvrir les câbles dénudés
dépassant la borne.
REMARQUES :
Utiliser uniquement les vis fournies.
Par mesure de sécurité, connecter les fils de la batterie en
dernier.
Pour éviter le débranchement des conducteurs ou de faire
tomber l’appareil, ne pas saisir les conducteurs lors du
transport de l’appareil.
•
•
•
•
•
2. Quite aproximadamente 7 – 10mm (9/32” – 3/8”) de aislación
de los extremos de los alambres. (Fig. 5)
NOTAS:
Si el largo de los conductores sin aislación es demasiado
corto, las conexiones podrán quedar mal hechas, lo que a
su vez podrá causar fallas de operación o interrupciones en
el sonido.
Por otro lado, si los conductores sin aislación son demasiado
largos, podrán producirse cortocircuitos eléctricos.
3. Apriete el tornillo hexagonal (incluido) para fijar el cable. (Fig.
6)
Antes de hacer esta conexión, use un manguito
aislante contraíble para cubrir los cables expuestos que
sobresalen del terminal.
NOTAS:
Use sólo los tornillos incluidos.
Por razones de seguridad, conecte los cables de a batería al
final.
Para evitar la desconexión de los alambres o la caída de la
unidad, asegúrese de no coger los alambres para transportar
la unidad.
•
•
•
•
•
CONN
Please
listed b
Remote
a. The h
anten
b. The h
radio
c. The h
negat
when
powe
If any
your M
powe
as clo
meth
long a
If this
switc
instal
switc
MRX-
acces
the ve
on an
A Blue/
B Powe
C Remo
D To ot
E SPST
F Fuse
G As clo
H Ignit
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine MRX-M50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine MRX-M50 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info