64016
4
Zoom out
Zoom in
Previous page
1/20
Next page
4
Español
Français
English
INSTALLATION
Due to the high power output of the MRP-F450/MRP-
F250, considerable heat is produced when the amplifier
is in operation. For this reason, the amplifier should be
mounted in a location which will allow for free circula-
tion of air, such as inside the trunk. For alternate instal-
lation locations, please contact your authorized Alpine
dealer.
1. Using the amplifier as a template, mark the four screw
locations.
2. Make sure there are no objects behind the surface
that may become damaged during drilling.
3. Drill the screw holes.
4. Position the MRP-F450/MRP-F250 over the screw
holes, and secure with four self-tapping screws.
NOTE:
To securely connect the ground lead, use an already in-
stalled screw on the metal part of the vehicle (marked
()). Be sure this is a good ground by checking conti-
nuity to the battery (–) terminal. As much as possible
connect all equipment to the same ground point. These
procedures will help eliminate noise.
Self-Tapping Screws (M4 x 20)
Ground Lead
Chassis
Holes
INSTALLATION
En raison de la sortie de puissance élevée du MRP-F450/
MRP-F250, une forte chaleur est produite pendant le
fonctionnement de l'amplificateur. Pour cette raison,
l'amplificateur doit être monté dans un endroit permet-
tant une bonne ventilation, tel que le coffre. Pour ce qui
concerne les différentes positions d'installation, contac-
ter un concessionnaire Alpine.
1. Apposer l'amplificateur contre la surface d'installa-
tion pour marquer les repères des quatre vis.
2. Vérifier qu'il n'y a pas d'objets derrière la surface
pouvant être abîmés lorsque les trous soient percés.
3. Percer les trous pour les vis.
4. Positionner le MRP-F450/MRP-F250 par dessus les trous
et fixer avec les quatre vis auto-taraudées.
REMARQUE:
Pour connecter solidement le conducteur de mise à la terre,
utiliser la vis déjà fixée sur la partie métallique du véhicule
(signalée ()). Assurez-vous que ce point est une bonne mise
à la terre en vérifiant la continuité à la borne de la batterie (–).
Si possible, connecter tout l'équipement au même point de
mise à la terre. Ceci vous aidera à éliminer le bruit.
Vis auto-taraudées (M4 x 20)
Conducteur de mise à la terre
Châssis
Trous
INSTALACIÓN
Debido a la salida de alta potencia del MRP-F450/MRP-F250,
se produce un calor considerable cuando el amplificador está
en funcionamiento. Por esta razón, el amplificador deberá
montarse en una ubicación que permita la libre circulación
de aire, como por ejemplo dentro del maletero. Para ubica-
ciones de instalación alternativas, por favor contacte a su dis-
tribuidor de Alpine autorizado.
1. Utilizando el amplificador como plantilla, marque la
ubicación de los cuatro tornillos.
2. Asegúrese de que no hay objeto alguno bajo la su-
perficie que pueda verse dañado durante la perfora-
ción de los agujeros.
3. Perfore los agujeros para los tornillos.
4. Sitúe el MRP-F450/MRP-F250 sobre dichos agujeros, y
asegúrelo con cuatro tornillos autorroscantes.
NOTA:
Para conectar de forma segura el cable de tierra, utilice un
tornillo ya instalado en la parte metálica del vehículo (marca-
do ()). Asegúrese de que es un punto de tierra bueno veri-
ficando la continuidad con el terminal de la batería (–). Co-
necte siempre que sea posible todo el equipo en el mismo
punto de tierra. Esto ayudará a eliminar el ruido.
Tornillos autorroscantes (M4 x 20)
Cable de tierra
Chasis
Agujeros
Fig. 1
1
4
3
2
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine MRP-F450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine MRP-F450 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info