168542
5
Zoom out
Zoom in
Previous page
1/24
Next page
5
EspañolFrançais
English
INSTALLATION
Due to the high power output of the MRD-M1005/
MRD-M605, considerable heat is produced when the
amplifier is in operation. For this reason, the amplifier
should be mounted in a location which will allow for
free circulation of air, such as inside the trunk. For
alternate installation locations, please contact your
authorized Alpine dealer.
1. Using the amplifier as a template, mark the four
screw locations.
2. Make sure there are no objects behind the surface
that may become damaged during drilling.
3. Drill the screw holes.
4. Position the MRD-M1005/MRD-M605 over the
screw holes, and secure with four self-tapping
screws.
NOTE:
To securely connect the ground lead, use an already
installed screw on the metal part of the vehicle
(marked ()). Be sure this is a good ground by
checking continuity to the battery (–) terminal. As
much as possible connect all equipment to the same
ground point. These procedures will help eliminate
noise.
Self-Tapping Screws (M4 x 20)
Ground Lead
Chassis
Holes
INSTALLATION
En raison de la sortie de puissance élevée du MRD-
M1005/MRD-M605, une forte chaleur est produite
pendant le fonctionnement de l'amplificateur. Pour
cette raison, l'amplificateur doit être monté dans un
endroit permettant une bonne ventilation, tel que le
coffre. Pour ce qui concerne les différentes positions
d'installation, contacter un concessionnaire Alpine.
1. Apposer l'amplificateur contre la surface d'installa-
tion pour marquer les repères des quatre vis.
2. Vérifier qu'il n'y a pas d'objets derrière la surface
pouvant être abîmés lorsque les trous soient
percés.
3. Percer les trous pour les vis.
4. Positionner le MRD-M1005/MRD-M605 par dessus
les trous et fixer avec les quatre vis auto-taraudées.
REMARQUE:
Pour connecter solidement le conducteur de mise à la terre,
utiliser la vis déjà fixée sur la partie métallique du véhicule
(signalée ()). Assurez-vous que ce point est une bonne
mise à la terre en vérifiant la continuité à la borne de la
batterie (–). Si possible, connecter tout l'équipement au
même point de mise à la terre. Ceci vous aidera à éliminer
le bruit.
Vis auto-taraudées (M4 x 20)
Conducteur de mise à la terre
Châssis
Trous
INSTALACION
Debido a la salida de alta potencia del MRD-M1005/MRD-
M605, se produce un calor considerable cuando el
amplificador está en funcionamiento. Por esta razón, el
amplificador deberá montarse en una ubicación que
permita la libre circulación de aire, como por ejemplo
dentro del maletero. Para ubicaciones de instalación
alternativas, por favor contacte a su distribuidor de Alpine
autorizado.
1. Utilizando el amplificador como plantilla, marque la
ubicación de los cuatro tornillos.
2. Asegúrese de que no hay objeto alguno bajo la
superficie que pueda verse dañado durante la
perforación de los agujeros.
3. Perfore los agujeros para los tornillos.
4. Sitúe el MRD-M1005/MRD-M605 sobre dichos
agujeros, y asegúrelo con cuatro tornillos
autorroscantes.
NOTA:
Para conectar de forma segura el cable de tierra, utilice un
tornillo ya instalado en la parte metálica del vehículo
(marcado ()). Asegúrese de que es un punto de tierra
bueno verificando la continuidad con el terminal de la
batería (–). Conecte siempre que sea posible todo el equipo
en el mismo punto de tierra. Esto ayudará a eliminar el
ruido.
Tornillos autorroscantes (M4 x 20)
Cable de tierra
Chasis
Agujeros
Fig. 4
3
2
1
4
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine mrd m1005 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine mrd m1005 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info