661050
11
Zoom out
Zoom in
Previous page
1/96
Next page
11-EN
EN
Initial System Start-Up
Press the RESET switch when using the unit for the rst time, after
changing the car battery, etc.
1 Turn off the unit power.
2 Press RESET switch with a ballpoint pen or similar
pointed object.
RESET switch
Note
Pressing the reset button will erase the clock setting and some
stored contents.
Setting the Clock
1 Press HOME, then touch [Settings].
2 Touch
,
then touch [Clock Adjust].
The setting display appears.
3 Touch
/
to set the hour and minute.
4 Touch [Set].
The setting is complete.
To activate/deactivate the CT function (page 13), touch [Clock Time].
Preparing a BLUETOOTH Device
You can enjoy music, or perform handsfree calling, by connecting a
suitable BLUETOOTH device (mobile phone, audio device, etc.). For
details on connecting a BLUETOOTH device, refer to the operating
instructions supplied with the device. Before connecting, turn down
the volume of this unit; otherwise, loud sound may result.
Pairing and connecting with a BLUETOOTH
device
When connecting a BLUETOOTH device for the first time, mutual
registration (called “pairing”) is required. Pairing enables this unit and
other devices to recognize each other.
1 Press HOME, then touch [Settings].
2 Touch
,
3 Touch [Bluetooth Connection], then set the signal to
[ON].
The BLUETOOTH signal of this unit is activated and
appears
on the status bar.
4 Touch [Pairing].
The unit enters pairing standby mode.
5 Perform the pairing procedure on the BLUETOOTH
device to detect this unit.
6 Select “IVE-W560” shown in the display of the
BLUETOOTH device.
7 If passkey* input is required on the BLUETOOTH device,
input [0000].
* Passkey may be called “passcode,” “PIN code,” “PIN number,”
“password,” etc., depending on the BLUETOOTH device.
8 Select this unit on the BLUETOOTH device to establish
the BLUETOOTH connection.
or lights up when the connection is made.
Note
While connected to a BLUETOOTH device, this unit cannot be
detected by another device. To enable detection, terminate the
current connection.
Connecting with a paired BLUETOOTH
device
This chapter explains how to connect manually to registered
BLUETOOTH devices.
1 Make sure that the BLUETOOTH signals both on this unit
(page 19) and the BLUETOOTH device are activated.
on the status bar indicates that the BLUETOOTH signal on this
unit is on.
2 Operate the BLUETOOTH device to connect to this unit.
or appears.
When the ignition is turned to on with the BLUETOOTH signal
activated, this unit searches for the last-connected BLUETOOTH
device, and if possible connection is made automatically.
Note
If this unit cannot detect the last-connected BLUETOOTH device,
touch [Reconnect] to search for the last-paired device again.
If the problem is not solved, follow the pairing procedure.
To install the microphone
To capture your voice during handsfree calling, you need to install
the microphone (included).
For details on how to connect the microphone, refer to the supplied
“Installation/Connections” guide.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine IVE-W560BT-R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine IVE-W560BT-R in the language / languages: English, German, French as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info