572055
59
Zoom out
Zoom in
Previous page
1/121
Next page
59-EN
About the Crossover
Crossover (X-OVER):
This unit is equipped with an active crossover. The crossover limits the
frequencies delivered to the outputs. Each channel is controlled
independently. Thus, each speaker pair can be driven by the frequencies
for which they have been optimally designed.
The crossover adjusts the HPF (high pass filter) or LPF (low pass filter)
of each band, and also the slope (how fast the filter rolls off the highs or
lows).
Adjustments should be made according to the reproduction
characteristics of the speakers. Depending on the speakers, a passive
network may not be necessary. If you are unsure about this point, please
consult your authorised Alpine dealer.
HPF (high pass filter): Cuts the lower frequencies and allows the
higher frequencies to pass.
LPF (low pass filter): Cuts the higher frequencies and allows the
lower frequencies to pass.
Slope: The level change (in dB) for a frequency change of one octave.
The higher the slope value, the steeper the slope becomes.
Adjust the slope to FLAT to bypass the HP or LP filters.
Do not use a tweeter without the HPF on or set to a low frequency, as
it may cause damage to the speaker due to the low frequency content.
You cannot adjust the crossover frequency higher than the HPF or
lower than the LPF.
Adjustment should be made according to the recommended crossover
frequency of the connected speakers. Determine the recommended
crossover frequency of the speakers. Adjusting to a frequency range
outside that recommended may cause damage to the speakers.
For the recommended crossover frequencies of Alpine speakers, refer
to the respective Owner’s Manual.
We are not responsible for damage or malfunction of speakers caused
by using the crossover outside the recommended value.
Source Setup Operation
1
Touch [Setup] icon of Top banner.
The Setup main screen is displayed.
2
Touch [ (Source)].
The Source Setup screen appears.
3
Select the desired item.
Setting items: Source Layout / Disc / Radio / DAB / AUX / RSE /
TuneIt
4
Touch [] or [] etc., to change its setting.
When the pop-up window for setup is displayed, touch [] to
close the window after setting.
5
Touch [] to return to the previous screen.
Immediately after changing the Source Setup (while the system is
writing data automatically) do not turn the ignition key to OFF.
Otherwise, the settings may not be changed.
Cut-off frequency
(1/3 octave steps)
Slope
Level
HPF LPF HPF LPF
Low range
speaker
----
20 Hz -
200 Hz
----
FLAT,
6,
12,
18,
24 dB/oct.
0 to
–12 dB
Rear high
range
speaker
20 Hz -
200 Hz
----
FLAT, –6,
–12, –18,
–24 dB/oct.
----
0 to
–12 dB
Front high
range
speaker
20 Hz -
200 Hz
----
FLAT, –6,
–12, –18,
–24 dB/oct.
----
0 to
–12 dB
Low range High range
(Different from actual display)
Level adjusting
(0 to –12 dB)
Output frequency range
Slope FLAT
Slope adjusting
20 Hz
HPF cut-off
frequency
LPF cut-off
frequency
(Different from actual display)
Source Setup
The following steps 1 to 5 are common operations to each
“Setting item” of Source Setup. Refer to each section for details.
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine INE-W987D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine INE-W987D in the language / languages: English as an attachment in your email.

The manual is 13,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alpine INE-W987D

Alpine INE-W987D User Manual - German - 121 pages

Alpine INE-W987D User Manual - Dutch - 121 pages

Alpine INE-W987D User Manual - French - 121 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info