572051
20
Zoom out
Zoom in
Previous page
1/52
Next page
20-EN
The subwoofer output phase is toggeled between SUBWOOFER
NORMAL (0°) or SUBWOOFER REVERSE (180°). Depending on the
installation location of your subwoofer, one of these settings may sound
better than the other.
Setting item: SUBW PHASE
Setting contents:
NORMAL (Initial setting) / REVERSE
When the subwoofer is on, you can select either SYSTEM 1 or SYSTEM
2 for the desired subwoofer effect.
Setting item: SUBW SYS
Setting contents:
SYSTEM 1 / SYSTEM 2 (Initial setting)
SYSTEM 1:
Subwoofer level changes according to the main volume setting.
SYSTEM 2:
Subwoofer level change is different from the main volume setting.
For example, even at low volume settings, the subwoofer is still
audible.
You can change the unit of time correction (centimetres or inches).
Setting item: LENGTH
Setting contents:
CM (Initial setting) / INCH
CM:
Time correction value is in centimetres.
INCH:
Time correction value is in inches.
Before performing the following, refer to “About Time Correction” on
page 21.
1
Turn the Rotary encoder to select the desired speaker
after selecting TCR, and then press ENTER.
FRONT-L FRONT-R REAR-L REAR-R SUBW-L
SUBW-R FRONT-L
2
Turn the Rotary encoder to adjust the distance of the
selected speaker, and then press ENTER.
0.0 cm to 336.6 cm (3.4 cm/step)
0.0 inch to 132.7 inch (1.3 inch/step)
Note
The total adjustment distance for all speakers should be less than 510
centimetres (201 inches).
3
Repeat steps 1 and 2 for setting other speakers.
By setting these values, sound from all speakers can be made to
reach the listener at the same time.
Connecting to an External Amplifier (POWER IC)
When an external amplifier is connected, sound quality can be
improved by stopping the power supply of the built-in amplifier.
Setting item: POWER IC
Setting contents:
ON (Initial setting) / OFF
ON:
The speakers are driven by the built-in amplifier.
OFF:
Use this mode when the line output of this unit is used to drive an
external amplifier. In this setting, the head units internal amplifier
is turned OFF and cannot drive speakers.
Notes
For more details about 2WAY/3WAY system mode. Please refer to
“Switching the 2WAY/3WAY system mode” and “About the 2WAY/
3WAY system mode” on page 24.
No sound is produced by the system when the power output is set to
OFF.
Setting the Subwoofer Phase
Setting the Subwoofer System
Setting the Time Correction Unit
(LENGTH)
Adjusting the Time Correction (TCR)
External Device
Amplier
ON: Speakers
(White)
(White/Black)
(Grey/Black)
(Grey)
(Green)
(Green/Black)
(Violet/Black)
(Violet)
2WAY system 3WAY system
Front high
range (L)
High
range (L)
Front high
range (R)
High
range (R)
Rear high
range (L)
Mid
range (L)
Rear high
range (R)
Mid
range (R)
Front high
range (L)
High
range (L)
Front high
range (R)
High
range (R)
Rear high
range (L)
Mid
range (L)
Rear high
range (R)
Mid
range (R)
OFF:
Amplier
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine CDE-W296BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine CDE-W296BT in the language / languages: English as an attachment in your email.

The manual is 4,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alpine CDE-W296BT

Alpine CDE-W296BT Quick start guide - English, German - 132 pages

Alpine CDE-W296BT User Manual - German - 57 pages

Alpine CDE-W296BT Quick start guide - Dutch - 132 pages

Alpine CDE-W296BT User Manual - Dutch - 57 pages

Alpine CDE-W296BT Quick start guide - French, Italian, Polish, Swedish, Spanish - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info