471377
14
Zoom out
Zoom in
Previous page
1/35
Next page
15-EN
Adjusting Subwoofer Level/Bass Level/
Treble Level/Balance (Between Left and
Right)/Fader (Between Front and Rear)/
Defeat
1
Press Rotary encoder (AUDIO) repeatedly to choose the
desired mode.
Each press changes the mode as follows:
SUBWOOFER
*
BASS LEVEL TRE LEVEL BALANCE FA DER
DEFEAT VOLUME SUBWOOFER
* When the subwoofer mode is set to OFF, its level cannot be
adjusted.
Note
If no operation is performed for 5 seconds, the unit automatically
returns to normal mode.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of BASS
LEVEL and TRE LEVEL will return to the factory defaults.
Setting the Bass/Treble/High Pass Filter
Use steps 1 to 3 to select one of the setting modes to modify. See the
applicable section below for details about the selected setting item.
1
Press SOUND to select the desired Sound Setting
mode.
BASS TREBLE HPF BASS
2
Turn the Rotary encoder or press BANDTA , SOURCE
etc., to change the setting.
3
Press and hold ESC for at least 2 seconds to return to
normal mode.
Notes
If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
The function is inoperable when DEFEAT is set to ON.
You can change the Bass Frequency emphasis to create your own tonal
preference.
Setting item: BASS
Setting the Bass Centre Frequency
Press BANDTA to select the desired bass centre
frequency.
80 Hz 100 Hz 200 Hz 60 Hz 80 Hz
Emphasises the displayed bass frequency ranges.
Setting the Bass Bandwidth
Press SOURCE to select the desired bass bandwidth.
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above and
below the centre frequency. A narrower setting will boost only
frequencies near the centre frequency.
Setting the Bass Level
Turn the Rotary encoder to select the desired bass level
(-7~+7)
*
.
You can emphasise or weaken the bass level.
* The adjustment can also be made by pressing Rotary encoder.
Refer to “Adjusting Subwoofer Level/Bass Level/Treble Level/
Balance (Between Left and Right)/Fader (Between Front and
Rear)/Defeat” on page 15.
Note
The bass level settings will be individually memorized for each source
(FM, MW (LW), CD, etc.) until the setting is changed. The bass
frequency and bass bandwidth settings adjusted for one source are
effective for all other sources (FM, MW (LW), CD, etc.).
You can change the Treble Frequency emphasis to create your own tonal
preference.
Setting item: TREBLE
Setting the Treble Centre Frequency
Press BANDTA to select the desired treble centre
frequency.
10.0 kHz 12.5 kHz 15.0 kHz 17.5 kHz 10.0 kHz
Emphasises the displayed treble frequency ranges.
Sound Setting
Subwoofer +0 ~ +15
Bass level -7 ~ +7
Treble level -7 ~ +7
Balance L15 ~ R15
Fader R15 ~ F15
Defeat ON/OFF
Volume 0 ~ 35
BAND/TA
/SOUND
SOURCE/
/ESC
Rotary encoder (AUDIO/LOUD)
Setting the Bass Control
Setting the Treble Control
(Narrow)
(Wide)
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine CDE-125BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine CDE-125BT in the language / languages: English as an attachment in your email.

The manual is 3,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alpine CDE-125BT

Alpine CDE-125BT User Manual - German - 38 pages

Alpine CDE-125BT Usermanual and installation guide - Dutch - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info