731984
19
Zoom out
Zoom in
Previous page
1/28
Next page
13
EN
Sharpening must be done taking account of the
type of blade and cutting edges, using a at le
and working all the points equally.
The references for correct sharpening are given
in Fig. 19:
A = Incorrect sharpening
B = Sharpening limits
C = Incorrect and unequal angles
It is important to retain the correct balance after
sharpening.
3 point blades can be used from both sides. When
one side of the points is worn, the blade can be
turned and the other side used.
WARNING!
The blade must never be
repaired, but must be replaced as soon as
signs of breaking are noted or the sharpening
limit is exceeded.
HEAD LINE REPLACEMENT (Fig. 20)
– Follow the sequence indicated in the gure.
SHARPENING THE LINE CUTTING KNIFE
(Fig. 21)
Remove the line cutting knife (1) from the guard
(2) by unscrewing the screws (3).
Fix the line cutting knife in a vice and sharpen it
using a at le, being careful to retain the origi-
nal cutting angle.
– Ret the knife on the guard.
EXTRAORDINARY MAINTENANCE
All maintenance operations not foreseen in this
manual must be performed exclusively by your
dealer.
All and any operations performed in unauthorised
centres or by unqualied persons will totally invali-
date the warranty.
STORAGE
After every work stint, clean the machine thor-
oughly to remove all dust and debris, and repair
or replace any faulty parts.
The machine must be stored in a dry place away
from the elements and with the cover correctly
tted.
LONG PERIODS OF DISUSE
IMPORTANT
If you are not going to use
the machine for a period of more than 2-3
months, we recommend you do a few things
before putting it away. This will make it eas-
ier when you want to use the machine again
and will also prevent permanent damage to
the engine.
• Storage
Before putting the machine away:
– Empty the fuel tank.
Start the engine and run it idle until it comes to
a halt, so that it uses up all the fuel that is left in
the carburettor.
Wait for the engine to cool down and remove
the spark plug
Pour a teaspoon of fresh oil into the spark plug
hole.
Pull the starter rope several times to deliver oil
to the cylinder.
Replace the spark plug with the piston in the
dead end upper position (visible from the spark
plug slot when the piston is at maximum stroke).
Restarting work
When you wish to start using the machine again:
– Remove the spark plug.
Pull the starter rope a few times to eliminate
excess oil.
Check the spark plug as described in chapter
“Checking the spark plug”.
Prepare the machine as indicated in the para-
graph entitled “Preparing for work”.
MAINTENANCE AND STORAGE
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpina TB 420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpina TB 420 in the language / languages: All languages as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info