731983

Alpina TB 320 D Manual

18
Zoom out
Zoom in
Previous page
1/28
Next page
12
EN
– Wash the lter element (2) with soap and wa ter.
Do not use petrol or other solvents.
– Leave the lter to dry in the open air.
– Fit the lter element (2) and the cover (1) back
on, tightening the knob (3) again.
CHECKING THE SPARK PLUG (Fig. 17)
Periodically remove and clean the spark plug us-
ing a metal brush to get rid of any deposits.
Check and reset the correct distance between the
electrodes.
Replace the spark plug and fasten it rmly using
the supplied wrench.
The spark plug must be replaced with one with
the same characteristics whenever the electrodes
have burnt or the insulation has worn, and in any
case every 100 working hours.
TUNING THE CARBURETTOR
The carburettor is tuned by the manufacturer to
achieve maximum performance in all situations,
with a minimum emission of toxic gas in compli-
ance with the regulations in force.
In the case of poor performance contact your
Dealer for a check of the carburetion and engine.
• Tuning minimum speed
WARNING!
The cutting device must
not move when the engine is running idle. If
the cutting device moves when the engine is
running idle, contact your dealer to correctly
regulate the engine.
ANGLE TRANSMISSION (Fig. 18)
Lubricate with lithium-based grease.
Remove the screw (1) and put in the grease, turn-
ing the shaft manually until grease emerges, then
replace the screw (1).
SHARPENING THE 3 POINT BLADE (Fig. 19)
WARNING!
Use protective gloves. If
sharpening is done without removing the
blade, disconnect the spark plug cap.
Correct maintenance is essential to maintain the
original eciency and safety of the machine over
time.
WARNING!
During maintenance ope-
ra tions:
– Remove the spark plug cap.
– Wait until the engine is suciently cold.
– Use protective gloves when handling the
blades.
– Keep the blade protection device on, except
when intervening directly on the blade.
– Never dispose of oils, fuel or other pollut-
ing materials in unauthorised places.
CYLINDER AND SILENCER
To reduce re risks, periodically clean the cylinder
aps with compressed air and clear the silencer
area to get rid of sawdust, branches, leaves or
other debris.
STARTING SYSTEM
To avoid overheating and damage to the engine,
always keep the cooling air vents clean and free
of sawdust and debris.
The starter rope must be replaced as soon as it
shows signs of wear.
NUTS AND SCREWS
Periodically check that all the nuts and screws are
securely tightened and the handgrips are tightly
fastened.
CLEANING THE AIR FILTER (Fig. 16)
IMPORTANT
Cleaning the air filter is
essential to guarantee the eciency and du-
ration of the machine. Do not work with a
damaged filter or without a filter, as this
could permanently damage the engine.
It must be cleaned after every 8-10 working hours.
Clean the lter as follows:
– Loosen the knob (3), remove the cover (1) and
the lter element (2).
MAINTENANCE AND STORAGE
8. MAINTENANCE AND STORAGE
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpina TB 320 D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpina TB 320 D in the language / languages: All languages as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info