Manual Alpina T 26 J (page 22 of 27) (All languages)

731918

Zoom out

Zoom in

1/27

e) Adjusting line length when working

(Fig. 10)

This machine is tted with a “Tap & Go” head.

To release more line, tap the cutting line head

against the ground with the engine at top speed:

the line will be released automatically and the

knife will cut o the excess length.

4.2 WHEN WORK IS FINISHED

When you have nished your work:

– Stop the machine as indicated previously (see

3.3).

5. ROUTINE MAINTENANCE

Correct maintenance is essential to maintain

the original eciency and safety of the machine

over time.

WARNING! During maintenance opera-

tions:

– Remove the spark plug cap.

– Wait until the engine is sufficiently cold.

– Never dispose of oils, fuel or other pollut-

ing materials in unauthorised places.

5.1 STORAGE

At the end of each working session, carefully

clean the machine of dust and debris, and make

sure that there are no damaged parts, replacing

any faulty parts. The machine must be stored in

a dry place away from the elements and with the

cover correctly tted.

5.2 CLEANING THE ENGINE

AND THE SILENCER

To reduce re risks, periodically clean the cylin-

der ns with compressed air and clear the silenc-

er area to get rid of sawdust, branches, leaves or

other debris.

5.3 STARTING UNIT

To avoid overheating and damage to the engine,

always keep the cooling air vents clean and free

of sawdust and debris.

If you notice signs of wear on the starter cable,

contact your Dealer for a replacement.

5.4 NUTS AND SCREWS

Periodically check that all the nuts and screws

are securely tightened and the handgrips are

tightly fastened.

5.5 CLEANING THE AIR FILTER (Fig. 11)

IMPORTANT Cleaning the air filter is essential to

guarantee the efficiency and duration of the ma-

chine. Do not work with a damaged filter or with-

out a filter, as this could permanently damage the

engine.

It must be cleaned after every 15 working hours.

Clean the lter as follows:

– Loosen the knob (3), remove the cover (1) and

the lter element (2).

– Wash the lter element (2) with soap and wa-

ter. Do not use petrol or other solvents.

– Leave the lter to dry in the open air.

– Fit the lter element (2) and the cover (1) back

on, tightening the knob (3) again.

5.6 CHECKING THE SPARK PLUG ( (Fig. 12)

Periodically remove and clean the spark plug us-

ing a metal brush to get rid of any deposits.

Check and reset the correct distance between

the electrodes.

Replace the spark plug and fasten it rmly using

the supplied wrench.

The spark plug must be replaced with one with

the same characteristics whenever the elec-

trodes have burnt or the insulation has worn, and

in any case every 100 working hours.

5.7 HEAD LINE REPLACEMENT (Fig. 13)

- Follow the sequence indicated in the gure.

5.8 SHARPENING THE LINE CUTTING

KNIFE (Fig. 14)

– Remove the line cutting knife (1) from the

guard (2) by unscrewing the screws (3).

– Fix the line cutting knife in a vice and sharpen

it using a at le, being careful to retain the

original cutting angle.

– Ret the knife on the guard.

5.9 LONG PERIODS OF DISUSE

IMPORTANT If you are not going to use the ma-

chine for a period of more than 2-3 months, we

recommend you do a few things before putting it

away. This will make it easier when you want to

use the machine again and will also prevent per-

manent damage to the engine.

Before putting the machine away:

– Empty the fuel tank.

– Start the engine and run it idle until it comes to

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina T 26 J in the language / languages: All languages as an attachment in your email.

The manual is 1,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina T 26 J Manual

Product: