608381

Alpina C 46 Manual

37
Zoom out
Zoom in
Previous page
1/460
Next page
This product has accordingly been designed with
a ventilation hatch on the right side of the surface
of the cylinder cover to allow warm air to be sup-
plied to the engine and to thereby prevent icing
from occurring.
Under normal circumstances the product should be
used in the normal operating mode, i.e., in the
mode which it is set at the time of shipment. How-
ever when the possibility exists that icing may oc-
cur, the unit should be set to operate in the anti-
freeze mode before use.
To switch from “Normal” mode to “Anti-freeze”
mode (and vice versa) (Fig. 11):
1. Switch the engine off.
2. Remove the air filter cover (1) and the air filter
(2).
3. Remove the choke (3) from the cylinder cover
(4).
4. Unscrew the screws (5) which secure the cylin-
der cover in place (three screws inside and one
outside) and remove the cylinder cover.
5. Use your fingers to press the anti-freeze cap (6)
on the right side of the cylinder cover and slide
it out from its seat.
6. Turn the anti-freeze cap (6) so that the "SNOW"
symbol is facing upwards and then replace the
cap.
7. Replace the cylinder cover and all the other
parts in their original position.
If the machine is used in anti-
freeze mode at higher temperatures, this may
cause difficulties when starting the engine and dur-
ing use due to the incorrect engine speed. Always
check that the machine is switched to normal mode
(with the "SUN" symbol facing upwards) if there is
no danger of ice forming.
NOTE
The chain speed is regulated by the throttle trigger
(1) on the rear handgrip (2).
The throttle trigger only works if the lockout (3) is
pressed at the same time.
The movement is transmitted from the engine to the
chain by a centrifugal mass clutch that prevents the
chain from moving when the engine is running at
minimum speed.
Do not use the machine if
the chain moves when the engine is running
idle; in this case, contact your dealer.
The correct running speed will be achieved by
pressing the throttle trigger (1) as far as possible.
Avoid using the engine at full
power for the first 6-8 working hours.
STOPPING THE ENGINE (Fig. 10)
To stop the engine:
– Release the throttle trigger (1) and allow the en-
gine to run idle for a few seconds.
– Set the switch (4) to «STOP».
When you have reduced
speed to a minimum, it may take a few sec-
onds for the chain to stop.
If the machine does not turn
off, pull the starter to flood and stop the engine and
immediately contact the dealer to find the cause of
the problem and request necessary repairs.
USING THE ANTI-FREEZE DEVICE
(excluding C 46 - XC 246 - C 50 - CP 45
- A 455 - MC 846 models) (Fig. 11)
Operating chain saws in temperatures of 0 – 5°C at
times of high humidity may result in ice forming
within the carburetor, and this in turn may cause the
output power of the engine to be reduced or for the
engine to fail to operate smoothly.
IMPORTANT
WARNING!
IMPORTANT
WARNING!
EN
HOW TO START - USE – STOP THE ENGINE 11
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpina C 46 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpina C 46 in the language / languages: All languages as an attachment in your email.

The manual is 8,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info