Manual Alpina C 1.8 (page 13 of 23) (All languages)

732004

Zoom out

Zoom in

1/23

8 PREPARING TO WORK / STARTING - STOPPING THE ENGINE

3. Press the safety button (6) and then the switch

(7).

NOTE

When you release the

switch, the safety button is also released and the

engine stops.

WARNING! The chain may take one

second to come to a stop after the engine is

switched o.

STOPPING THE ENGINE

To stop the engine:

– Release the switch (7).

– FIRST unplug the extension lead (3) from the

mains socket (4) and THEN disconnect the

power cable (2) of the machine from the exten-

sion lead (3).

STARTING THE ENGINE (Fig. 12)

Before starting the engine:

– Fasten the extension lead (1) to the cable clamp

on the rear handgrip.

– FIRST connect the power cable plug (2) to the

extension lead (3) and THEN plug the extension

lead into the mains socket (4).

– Take o the bar cover.

– Make sure the bar is not touching the ground or

any other object

To start the engine (Fig. 12):

1. Disengage the chain brake (5) by pulling the

front hand guard towards the front handgrip.

2. Hold the chain-saw rmly with both hands.

6. HOW TO START - STOP THE ENGINE

WARNING! Do not use the machine if

the chain brake does not function correctly

and have it inspected by your dealer.

4. CHAIN LUBRICANT

IMPORTANT

Only use chain-saw oil or

adhe sive oil for chain-saws. Do not use oil con-

taining impurities, to avoid clogging the tank lter

and permanently damaging the oiler.

IMPORTANT

The chain lubricating oil is

bio-degradable. The use of mineral oil or engine oil

can have a serious impact on the environment.

It is essential that you use good quality oil to lubri-

cate the cutting parts eectively.

Used or poor quality oil does not guarantee good

lubrication and reduces the duration of the chain

and bar.

IMPORTANT

Before each machine use,

the oil level should be checked and topped up to

1 cm from the rim of the ller. The oil level must not

drop below the «MIN» level mark.

5. ELECTRICAL CONNECTIONS

DANGER! Electricity and moisture

are not compatible.

– Always handle and connect electric cables

in dry conditions.

– Keep electric sockets or cables away from

wet and damp areas (e.g. puddles or wet

ground).

The quality of the extension leads must be no less

than H07RN-F or H07VV-F, with a minimum sec-

tion of 1.5 mm

and a recommended maximum

length of 30 m.

To avoid overheating, do not keep the extension

lead rolled up during use.

DANGER! The permanent connec-

tion of any electrical equipment to the mains

of a building must be installed by a qualied

electrician in conformity with the regulations

in force. Incorrect wiring can cause serious

injury and even death.

DANGER! Supply power to the ma-

chine using a dierential switch (RCD  Resid-

ual Current Device) with a tripping current of

max. 30 mA.

IMPORTANT

To prevent power supply ou-

tages:

– make sure that the electric system’s overall ca-

pacity is adequate;

– connect the machine to a mains socket with suf-

cient amperage;

– avoid simultaneous use of other electrical ap-

pliances with high power consumption.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina C 1.8 in the language / languages: All languages as an attachment in your email.

The manual is 1,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina C 1.8 Manual

Product: