731968
13
Zoom out
Zoom in
Previous page
1/21
Next page
PREPARING TO WORK / HOW TO START - STOP THE MOTOR
7
EN
1. CHECKING THE MACHINE
WARNING! Make sure the machine is
not plugged into the mains socket.
Before starting work please:
check that the mains frequency and voltage is
the same as the rating data on the “Identication
Plate” (see chap. 1 - 7.8).
check that the trigger switch and the safety
button (Only for SGT 600) should move freely
without forcing and return automatically and rap-
idly back to their neutral position;
(Only for SGT 600) check that the trigger
switch must remain locked until the safety but-
ton is pressed;
check that the cooling air vents are not ob-
structed;
check that the power cable and extension lead
are not damaged;
check that handgrips and protection devices
are clean and dry, correctly mounted and well
fastened to the machine;
check that the cutting devices and guards are
not damaged;
check that the machine is not showing signs of
wear or damage due to knocks or other causes,
and carry out the necessary repairs.
2. ELECTRICAL CONNECTIONS
DANGER! Electricity and moisture
are not compatible.
Always handle and connect electric cables
in dry conditions.
Keep electric sockets or cables away from
wet and damp areas (e.g. puddles or wet
ground).
The quality of the extension leads must be no less
than H07RN-F or H07VV-F, with a minimum sec-
tion of 1.5 mm and a recommended maximum
length of 30 m.
To avoid overheating, do not keep the extension
lead rolled up during use.
DANGER! The permanent connec-
tion of any electrical equipment to the mains
of a building must be installed by a qualied
electrician in conformity with the regulations
in force. Incorrect wiring can cause serious
injury and even death.
NOTE
(Only for SGT 600 ) When you release the switch,
the safety button is also released and the motor
stops.
STOPPING THE MOTOR (Fig. 4)
To stop the motor:
Release the switch (6).
FIRST unplug the extension lead (3) from the
mains socket (4) and THEN disconnect the
power cable (2) of the machine from the exten-
sion lead (3).
STARTING THE MOTOR (Fig. 4)
Before starting the motor:
Fasten the extension lead (1) to the cable clamp
on the rear handgrip.
FIRST connect the power cable plug (2) to the
extension lead (3) and THEN plug the extension
lead into the mains socket (4).
To start the motor:
Hold the machine rmly with both hands.
SGT 600: Press the safety button and then the
switch (6).
SGT 350: Press the switch (6).
6. HOW TO START - STOP THE MOTOR
5. PREPARING TO WORK
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpina ATR 350 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpina ATR 350 E in the language / languages: All languages as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info