Manual Alpina ATR 26 J (page 16 of 27) (All languages)

731964

Zoom out

Zoom in

1/27

condition and in particular:

– The throttle trigger and the safety lever must

move freely, they must not need forcing and

should return automatically and rapidly back

to the neutral position;

– The throttle trigger must remain locked until

the safety lever is pressed;

– The engine stop switch must easily move from

one position to the other;

– The electric cables and in particular the spark

plug cable must be in perfect condition to

avoid the generation of any sparks, and the

cap must be correctly tted on the spark plug;

– The machine handgrips and protection devic-

es must be clean and dry and well fastened to

the machine;

– Check the correct position of the handgrips

and the connection point of the harness, and

the proper balance of the machine.

– Make sure that the guards are suitable for the

cutting means being used and are tted cor-

rectly.

– There must be no signs of damage on the

cutting means. Make sure the cutting means

is not worn or damaged. Replace the dam-

aged or worn cutting means to preserve bal-

ance. Any repairs must be done at a special-

ised centre.

4) WARNING: DANGER! Petrol is highly

flammable.

– Keep the fuel in containers which have been

specically manufactured and homologated

for such use;

– add fuel, using a funnel, only outdoors; do not

smoke during this operation and each time fu-

el is handled;

– Slowly open the fuel tank to allow the pressure

inside to decrease gradually;

– Add fuel before starting the engine. Never re-

move the tank cap or add fuel while the engine

is running or when the engine is hot;

– if you have spilled some fuel, do not attempt to

ignite the engine but move the machine away

from the area of spillage and avoid creating

any source of ignition until the fuel has evapo-

rated and fuel vapours have dissipated:

– Always put the tank and fuel container caps

back on and tighten well;

– Immediately clean up all traces of fuel spilt on

the machine or on the ground;

– Never start the machine in the same place you

relled it with fuel; the engine must be started

in an area at least 3 metres from where you re-

lled the fuel tank;

– Make sure your clothing does not come into

contact with the fuel, on the contrary, change

your clothes before starting the engine.

5) Replace faulty or damaged silencers.

C) DURING USE

1) Do not operate the engine in a conned space

where dangerous carbon monoxide fumes can

develop.

2) Work only in daylight or with good articial

light in good visibility conditions. Keep per-

sons, children and animals away from the work-

ing area.

3) Always use caution and take on a rm and

well-balanced position

4) Where possible, avoid working on wet, slip-

pery ground or in any case on uneven or steep

ground that does not guarantee stability for the

operator;

5) Make sure you have a steady foothold on

slopes.

6) Never run, always walk.

7) Pay particular attention to uneven ground or

the presence of obstacles.

8) Always work across the face of the slope

and never up and down it, being very careful

when changing direction, making sure the cut-

ting means is always downstream.

9) Do not use the machine if you are unable to

hold it with both hands or keep it steady on your

legs while working.

10) The machine must never be used by more

than one person.

11) When working, the machine must always be

rmly held in both hands, keeping the power unit

on the right of the body and the cutting-means

assembly below the line of the belt.

14) Pay attention to trac when using the ma-

chine near roads.

13) Never use the machine with damaged or

missing guards.

14) Always keep hands and feet away from the

cutting means, when starting and when using

the machine.

15) Beware of injuries caused by devices used

to cut the line length. After releasing the new line,

always put the machine in a working position be-

fore starting the engine.

16) Be careful of ying debris coming from the

cutting means.

17) Warning: the cutting means continues to ro-

tate even after the engine has been switched o.

18) Make sure the machine is securely locked

when you start the engine:

– Check that there is nobody within at least 15

metres of the machine’s range of action or at

least 30 metres for heavier cutting;

– Do not direct the silencer and therefore the ex-

haust fumes towards inammable materials.

19) Do not change the engine settings or over-

speed the engine.

20) Do not strain the machine too much and do

not use a small machine for heavy-duty works.

If you use the right machine, you will reduce the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina ATR 26 J in the language / languages: All languages as an attachment in your email.

The manual is 1,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina ATR 26 J Manual

Product: