516562
29
Zoom out
Zoom in
Previous page
1/32
Next page
29
User’s manual
EN
5. Check the lower part of the robot (cutting blade area, and wheels), use
a brush suitable to remove deposits and/or residues that may impede
the proper functioning of the robot.
6. Remove any grass and leaves from the gripping areas of the robot.
7. Clean the knobs of the battery charger (A), the contact plates (B) and
remove any deposits or residuals caused by electric contacts with a
dry cloth and, if necessary, with ne sandpaper.
8. Clean the inside of the charging station to remove any accumulated
residuals.
charging knobs (A)
contact plates (B)
TROUBLESHOOTING
TROUBLESHOOTING GUIDE
The information below is designed to help identify and correct any faults and/or malfunctions which may occur during operation. Some faults can
be xed by the user, while others require speci c technical skills or special expertise and therefore must only be xed by quali ed personnel with
certi ed experience in the speci c eld of intervention.
Problem Cause Remedies
The antitheft alarm continues to
operate
Alarm enabled Disable the alarm (see “Programming Mode”)
The antitheft alarm does not work Alarm disabled Enable the alarm (see “Programming Mode”)
The robot is very noisy
Cutting blade damaged Replace the blade with a new one (see “Blade Replacement”)
Cutting blade clogged by residuals (tape, cords,
plastic fragments, etc.)
Safely stop the robot (see “Robot Safety Stop”). Unclog the
blade
Warning – Caution
Use protective gloves to prevent injuries to your hands
The robot was started in the presence of obstacles
(fallen branches, forgotten objects, etc.)
Stop the robot safely (see “Robot Safety Stop”)
Remove the obstacle and restart the robot (see “Start-up and
manual stopping of the robot (in closed areas)”)
Electric motor failure
Have the motor replaced or repaired by your nearest
authorised service centre
Grass too high
Increase the cutting height (see “Adjustment of cutting height”)
Carry out a preliminary cutting of the area with a normal
lawnmower
The robot does not position itself
correctly inside the charging station
Incorrect positioning of the perimeter wire or power
cord of the charging station
Check the connection of the charging station (see “Installation
of charging station and power supply unit”)
Collapsing of ground next to the charging station
Position the charging station on a at and stable surface (see
“Planning of system installation”)
The robot does not behave correctly
around the owerbeds
Perimeter wire laid incorrectly
Reposition the perimeter wire correctly (counter-clockwise
direction) (see “Installation of perimeter wire”)
The robot works at the wrong time
Clock was set incorrectly Reset the clock of the robot (see “Programming Mode”)
Working time was set incorrectly Reset the working time (see “Programming Mode”)
The robot does not execute quick
re-entry
Quick re-entry not setup correctly
Check the exact layout of the quick re-entry (see “Layout of the
robot’s quick re-entry to the charging station”)
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpina AR-2 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpina AR-2 400 in the language / languages: English as an attachment in your email.

The manual is 7,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Alpina AR-2 400

Alpina AR-2 400 User Manual - German - 32 pages

Alpina AR-2 400 User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info