Manual Alpina ACS 2.0 ET (page 15 of 23) (All languages)

732013

Zoom out

Zoom in

1/23

1. CHECKS DURING WORK

• Checking the chain tension

The chain tends to stretch gradually as you work,

so you need to check its tension frequently.

IMPORTANT

During the rst period of use

(or after replacing the chain), it must be checked

more frequently due to settling of the chain.

WARNING! Never work with the chain

loose, as it can be hazardous if the chain slips

out of its guides.

To adjust the chain tension, follow the instructions

in Chapter 5.2.

• Checking the oil delivery

IMPORTANT

Never use the machine with-

out lubrication! You can check the oil level in the

tank through the transparent gauge. Make sure

you ll up the oil tank every time you use the ma

chine.

WARNING! Make sure the bar and the

chain are in place when you check the oil de-

livery.

Start the engine and check if the chain oil is de li -

vered as shown in the gure (Fig. 13).

• Shutdown whilst working (Only for

C 2.2 E/ET – SE 2216 / 2216 Q - A 220 EQ)

Your chain saw is designed with an overload

protection with circuit breaker. If the chain saw is

clogged (e.g. blocking of the cutting means, chain

teeth jammed, overload cutting) during the cutting

operation, the overload circuit breaker will cut the

mains power supply automatically to protect your

chain saw.

IMPORTANT

The circuit breaker will be

activated when the cutting current is over 35-40A,

and it can be reset manually by pressing the reset

button (1.15) 30 seconds after it has cooled com-

pletely.

2. DIRECTIONS FOR USE AND CUTTING

TECHNIQUES

Before felling or delimbing for the rst time, prac-

tise sawing logs on the ground or on trestles, so

that you can get familiar with the machine and the

most suitable sawing techniques.

WARNING! Always hold the machine

with both hands when sawing.

WARNING! Stop the engine im me dia

tely if the chain stops during sawing. Be wa re

of kickback, which can occur if the bar con-

tacts an obstacle.

• Felling a tree

– When bucking and felling operations are being

performed by two or more persons at the sa me

time, the felling operations should be separated

from the bucking operation by a distance of at

least twice the height of the tree being felled.

Trees should not be felled in a man ner that

would endanger any person, stri ke any utility

line or cause any property damage. If the tree

does make contact with any u ti lity line, the com-

pany should be notied im mediately.

– The chain saw operator should keep on the up-

hill side of the terrain as the tree is likely to roll

or slide downhill after it is felled.

– An escape path should be planned and clea-

red as necessary before cuts are started. The

e scape path should extend back and diagonally

to the rear of the expected line of fall as illus-

trated in Figure 15.

– Before felling is started, consider the natural

lean of the tree, the location of larger branches

and the wind direction to judge which way the

tree will fall.

– Remove dirt, stones, loose bark, nails, staples

and wire from the tree.

• Notching undercut

Make the notch 1/3 the diameter of the tree, per-

pendicular to the direction of falls as illustrated in

Figure 16.

Make the lower horizontal notching cut rst.

his will help to avoid pinching either the saw chain

or the guide bar when the second notch is being

made.

10 USING THE MACHINE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina ACS 2.0 ET in the language / languages: All languages as an attachment in your email.

The manual is 1,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina ACS 2.0 ET Manual

Product: