732013

Alpina ACS 2.0 ET Manual

12
Zoom out
Zoom in
Previous page
1/23
Next page
PREPARING TO WORK 7
EN
1. CHECKING THE MACHINE
WARNING! Make sure the machine is
not plugged into the mains socket.
Before starting work please:
– check that the mains frequency and voltage is
the same as the rating data on the “identication
plate” (see chap. 1 - 10.8);
– ccheck that all the screws on the machine and
the bar are tightly fastened;
– check that the chain is tensioned correctly,
sharp and there are no signs of any damage;
– check that handgrips and protection devices
are clean and dry, correctly mounted and well
fastened to the machine;
– check that the chain brake is working eciently;
– check that the trigger switch and the safety
button should move freely without forcing and
return automatically and rapidly back to their
neutral position;
– check that the trigger switch must remain locked
until the safety button is pressed;
– make sure the cooling air vents are not clog ged
up with sawdust or debris;
– check that the power cable and extension lead
are not damaged;
– check that the chain’s oil level is not below the
«MIN» level mark and top up to 1 cm from the
rim of the ller if necessary.
2. CHECKING THE CHAIN TENSION
WARNING! Make sure the machine is
not plugged into the mains socket.
• MACHINES WITH STANDARD
CHAIN TENSION ADJUSTER
– Loosen the guard nut, using the wrench (Fig. 5).
– Turn the chain tension adjuster screw (4) to ad-
just the chain tension (Fig. 5).
– Raise the bar and tighten the guard nut securely
using the wrench (Fig. 6).
The tension is correct when the drive links do not
slip out of the chain guides if you hold the chain in
the middle of the bar (Fig. 7).
Loosen the brake by pressing both the switch
and the safety button. Using a screwdriver, run
the chain along the guides to check that it moves
smoothly.
• MACHINES WITH QUICK CHAIN TENSION
ADJUSTER
– Loosen the handle (11). (Fig. 5a).
– Turn the ring-nut (12) to obtain the desired chain
tension level (Fig. 5a).
– Raise the bar and tighten the handle (11)
securely (Fig. 6a).
The tension is correct when the drive links do not
slip out of the chain guides if you hold the chain in
the middle of the bar (Fig. 7).
Loosen the brake by pressing both the switch
and the safety button. Using a screwdriver, run
the chain along the guides to check that it moves
smoothly.
3. CHECKING THE CHAIN BRAKE
This machine is equipped with a double braking
system that intervenes in two situations:
a) When the switch lever is released, a brake
is automatically activated that slows and stops
chain movement, in order to prevent the risk of
injury should the chain continue to turn after it
has been switched o.
b) In the event of a kickback while working,
following an irregular contact of the tip of the
bar, with a brusque upward movement that
causes the hand to strike the front guard. In
this case, the brake blocks chain movement
and must be released manually in order to di-
sengage it.
This brake can be operated manually by pushing
the front guard forward. To release the brake, pull
the front guard towards the handgrip until you hear
a click.
To check that the brake works eciently, proceed
as follows:
– Start the engine by holding the front handgrip
and push the front hand guard forwards with
your thumb (towards the bar).
– When the brake is engaged, release the trigger
switch.
The chain must stop as soon as the brake is en-
gaged.
5. PREPARING TO WORK
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpina ACS 2.0 ET at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpina ACS 2.0 ET in the language / languages: All languages as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info