Manual Alpina ABR 26 JD (page 17 of 27) (All languages)

731917

Zoom out

Zoom in

1/27

risk of hazards and improve the quality of your

work.

21) Check that when the machine is running

idle, there is no movement of the cutting means

and, after pressing the throttle trigger, the engine

quickly returns to minimum speed.

22) Always keep the machine connected to the

harness when working.

23) Stop the engine:

– Whenever you leave the machine unattended;

– Before refuelling;

– When moving between work areas.

24) Stop the engine and disconnect the spark

plug cable:

– Before checking, cleaning or working on the

machine;

– After the intake of a foreign body. Inspect the

machine for damage and make repairs before

restarting and operating the machine;

– If the machine begins to vibrate abnormally

(Immediately look for the causes of the vibra-

tions and take it to a Specialised Centre for

necessary inspections);

– When the machine is not in use.

25) Avoid using the machine in environments or

at times of the day when it may disturb others.

26) To avoid the risk of re, do not leave the ma-

chine with the engine hot on leaves, dry grass or

other inammable material.

27) Never assemble metal cutting means. The

use of metal or rigid cutting means of any type

with this machine is prohibited.

28) WARNING – If something breaks or an ac-

cident occurs while working, turn o the engine

immediately and move the machine away to pre-

vent further damage; if an accident occurs with

injuries or third parties are injured, carry out the

rst aid measures most suitable for the situation

immediately and contact the medical authorities

for any necessary health care. Carefully remove

any debris that might cause damage or harm

persons or animals should it not be seen.

29) WARNING – The noise and vibration lev-

els shown in these instructions are the maxi-

mum levels for use of the machine. The use of

an unbalanced cutting means and the absence

of maintenance have a signicant inuence on

noise emissions and vibrations. Consequently,

it is necessary to take preventive steps to elimi-

nate possible damage due to high levels of noise

and stress from vibration. Maintain the machine

well, wear ear protection devices, and take

breaks while working.

30) Prolonged exposure to vibrations can cause

injuries and neurovascular disorders (also called

“Raynaud’s syndrome” or “white hand”), espe-

cially to people suering from circulation dis-

orders. The symptoms can regard the hands,

wrists and ngers and are shown through loss of

sensitivity, torpor, itching, pain and discolouring

of or structural changes to the skin. These ef-

fects can be worsened by low ambient temper-

atures and/or by gripping the handgrips exces-

sively tightly. If the symptoms occur, the length of

time the machine is used must be reduced and a

doctor consulted.

D) MAINTENANCE AND STORAGE

1) WARNING! – Before cleaning or doing main-

tenance work, disconnect the spark plug cap

and read the relevant instructions. Wear proper

clothing and protective gloves whenever your

hands are at risk.

2) WARNING! – Never use the machine with

worn or damaged parts. Faulty or worn-out parts

must always be replaced and not repaired. Use

original spare parts only: the use of non-original

and/or incorrectly tted parts will jeopardize the

safety of the machine, may cause accidents or

personal injuries for which the Manufacturer is

under no circumstance liable or responsible.

3) Any adjustments or maintenance operations

not described in this manual must be carried out

by your Dealer or a specialized Service Centre

with the necessary knowledge and equipment

to ensure that the work is done correctly main-

taining the machine’s original safety level. Any

operations performed in unauthorized centres or

by unqualied persons will totally invalidate the

Warranty and all obligations and responsibilities

of the Manufacturer.

4) After each use, disconnect the spark plug ca-

ble and check for damage.

5 Keep all nuts, bolts and screws tight to be sure

the machine is in safe working condition. Routine

maintenance is essential for safety and for main-

taining a high performance level.

6) Check that the cutting means screws are

properly tightened on a regular basis.

7) Wear work gloves and apply the cutting

means guard to handle, remove or remount the

same.

8) Be careful during adjustment of the machine

to prevent entrapment of the ngers between the

cutting means and xed parts of the machine.

9) Do not touch the cutting means until the spark

plug cable has been disconnected and the cut-

ting means is completely stationary. When serv-

icing the cutting means, bear in mind that, even

though the spark plug cable is disconnected, the

cutting means can still move.

10) Check the guard frequently for wear or dete-

rioration. Replace it if it is damaged.

11) Replace any instruction or warning message

stickers, if damaged.

12) Store the machine out of the reach of chil-

dren.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina ABR 26 JD in the language / languages: All languages as an attachment in your email.

The manual is 1,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina ABR 26 JD Manual

Product: