Manual Alpina ABR 26 J (page 20 of 122) (All languages)

731916

Zoom out

Zoom in

1/122

– Never dispose of oils, fuel or other polluting

materials in unauthorised places.

GREASING (Fig. 11)

– Grease every 20 hours using the specic grease

gun.

– Use lithium-based grease for high temperatures

and extreme pressures.

DANGER! During maintenance oper-

ations:

– Disassemble the pruner rod from the brush

cutter.

– Use protective gloves when handling the

bar and chain.

– Keep the bar protection devices on, except

when intervening directly on the bar or the

chain.

– ll the relevant tank with oil;

– check that all the screws on the machine and the

bar are tightly fastened;

– check that the chain is sharp and there are no

signs of any damage;

– check that handgrips and protection devices

are clean and dry, correctly mounted and well

fastened to the machine;

– check that the handgrips are well fastened;

– check the chain tension.

• Checking the oil delivery

DANGER! Make sure the bar and the

chain are in place when you check the oil de-

livery.

Start the engine, keep it running at medium power

and check if the chain oil is delivered as shown in

the gure (Fig. 10).

You can adjust the chain oil ow using a screw-

driver on the adjuster screw (1) of the oiler, which

is on the bottom of the machine (Fig. 10).

• Directions for use

– When starting the motor make sure the chain is

NOT resting on the ground and does not come

into contact with foreign bodies; for this purpose,

position the rod appropriately.

– Follow the instructions supplied with the brush

cutter to start the motor.

– Prune by making a rst cut from below on the

part to be cut, then cut from above, to avoid

barking and damage to the plant.

– When pruning operate outside the area in which

cut material falls.

– Never bring the cutting blades close to body

parts while working.

– Always t the bar guard when the device is

swtched o.

DANGER! Perform all operations

with the engine o.

– Unscrew the nut (1) and remove the cover (2) to

get to the drive sprocket and point where the bar

is to be tted (Fig. 2).

– Mount the bar (4) by inserting the stud bolt (3) in

the groove and push it towards the back of the

starter unit (Fig. 3).

– Mount the chain in the right direction around the

drive sprocket and along the bar rail (Fig. 4). If

the tip of the bar has a nose sprocket, make sure

the drive links t correctly in the sprocket rims.

– Check that the chain tension adjuster pin (5) is

tted properly in the hole on the bar; if it isn’t,

turn the chain tension adjuster screw (6) using

a screwdriver until the pin is completely inserted

(Fig. 5).

– Fit the guard (2) back on without tightening the

nut (1).

– Turn the chain tension adjuster screw (6) to ad-

just the chain tension (Fig. 6).

– Raise the bar (4) and tighten the nut (1) on the

guard (2) securely using the wrench (Fig. 7).

– Check the chain tension. The tension is correct

when the drive links do not slip out of the chain

guides if you hold the chain in the middle of the

bar (Fig. 8).

– Using a screwdriver, make the chain run along

the guides to check it moves smoothly without

resistance.

ATTACHING THE PRUNER (Fig. 9)

– Pull out the stop pin (1) and push the rod (2) right

down until the stop pin (1) clicks into the hole (3)

in the rod. This is easier to do if you rotate the

bottom of the rod (2) slightly in both directions.

The pin (1) is in place when it is completely lo-

dged in the hole.

– Once inserted, tighten the knob (4) securely.



Please also read the instructions manual for the

brush cutter the device pruner is applied to.

Before starting work please:

 18

  

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina ABR 26 J in the language / languages: All languages as an attachment in your email.

The manual is 3,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina ABR 26 J Manual

Product: