Manual Alpina A 405 (page 33 of 460) (All languages)

608380

Zoom out

Zoom in

1/460

screw (4) using a screwdriver until the pin is

completely inserted (Fig. 4).

– Turn the chain tension adjuster screw (4) to ad-

just the chain tension (Fig. 4).

– Raise the bar and tighten the guard nuts securely

using the wrench (Fig. 5).

•

Machines with quick chain tension

adjuster

(SP 375Q, SP 405Q, C 38 T, C 41 T)

– Unscrew the handle (11) and remove the guard

to get to the drive sprocket and the point where

the bar is fitted (Fig. 1A).

– Remove the plastic spacer, (12); this spacer

must be used exclusively when transporting the

machine in its packaging and must not be used

at any other time (Fig. 1A).

– Mount the bar (2) by inserting the stud bolts in

the groove and push it towards the back of the

machine body (Fig. 2).

– Mount the chain in the right direction around the

drive sprocket and along the bar rail (Fig. 3). If

the tip of the bar has a nose sprocket, make

sure the drive links fit correctly in the sprocket

rims.

– Fit the guard back on without tightening the han-

dle (11). Check that the chain tension adjuster

pin (14) is fitted properly in the hole on the bar;

if it isn’t, turn the chain tension adjuster ring-nut

(15) until the pin is completely inserted (Fig. 4A).

– Turn the ring-nut (15) to obtain the desired chain

tension level (Fig. 4A).

– Raise the bar and tighten the handle (11) se-

curely (Fig. 5A).

• Checking the chain tension

Check the chain tension. The tension is correct

when the drive links do not slip out of the chain

guides if you hold the chain in the middle of the bar

(Fig. 7).

The machine is supplied with

the bar and chain dismantled and the oil and fuel

tanks empty.

Unpacking and complet-

ing the assembly should be done on a flat and

stable surface, with enough space for machi-

ne handling and its packaging, always making

use of suitable equipment.

Disposal of the packaging should be done in

accordance with the local regulations in force.

Always wear heavy-duty

gloves when handling the bar and chain.

Mount the bar and chain very carefully so as

not to impair the safety and efficiency of the

machine. If in doubt, contact your dealer.

Before fitting the bar, make sure the chain brake is

not engaged; this is done by pulling the front hand

guard right back towards the body of the machine.

Perform all operations

with the engine off.

BAR AND CHAIN MOUNTING

• M

achines with standard chain tension

adjuster

– Unscrew the nuts and remove the clutch cover to

get to the drive sprocket and point where the bar

is to be fitted (Fig. 1).

– Remove the plastic spacer, (1); this spacer must

be used exclusively when transporting the ma-

chine in its packaging and must not be used at

any other time (Fig. 1).

– Mount the bar (2) by inserting the stud bolts in

the groove and push it towards the back of the

machine body (Fig. 2).

– Mount the chain in the right direction around the

drive sprocket and along the bar rail (Fig. 3). If

the tip of the bar has a nose sprocket, make

sure the drive links fit correctly in the sprocket

rims.

– Check that the chain tension adjuster pin (3) of

the clutch cover is fitted properly in the hole on

the bar; if it isn’t, turn the chain tension adjuster

WARNING!

IMPORTANT

MACHINE ASSEMBLY 7

4. MACHINE ASSEMBLY

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpina A 405 in the language / languages: All languages as an attachment in your email.

The manual is 8,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpina A 405 Manual

Product: