574293
6
Zoom out
Zoom in
Previous page
1/6
Next page
MPT-250B SPECIFICATIONS AND
OPERATING INSTRUCTIONS
DATASHEET
______________________________________________________________________
Daniels Manufacturing Corporation, 526 Thorpe Road, Orlando, FL 32824, U.S.A.
Phone: (407) 855-6161 Fax (407) 855-6884 www.dmctools.com Email: dmc@dmctools.com
Copyright©2013 All Rights Reserved Page 6 of 6 Rev. M 10/13 MPT-250B-DS
4.3.2 Depress the operating lever of the self tightening cam type upper grip to open far enough to accept the test
sample (wire). When you release the lever, the cam wheel will grip the wire.
4.4 SAMPLE OPERATION
The following is an example procedure for testing a wire specimen after the unit has successfully completed the
STARTUP SEQUENCE (section 4.1.4):
4.4.1 Place the terminal end of the wire sample in the Lower Grip (section 4.2).
4.4.2 Pull the sample to remove any slack in the wire and place the opposite end of the wire sample in the Upper Grip
(section 4.3).
4.4.3 Once the sample is taut between the grips, press the motor control START switch (section 3.3.1).
The pull wheel will turn in a clockwise motion thereby tightening the grip on the sample and applying tension to
the wire.
4.4.4 The unit will cease operation once the sample has failed (section 3.5.1) or the force limit has been reached.
Record the value indicated on the display panel.
4.4.5 Press the motor control RESET switch (section 3.3.1) to return the pull wheel to the start position to allow for
the next test.
4.4.6 Press the display control RESET switch (section 3.3.3) to return the display to zero.
4.4.7 Repeat steps 4.4.1 to 4.4.6.
5. CALIBRATION
The MPT-250B wire crimp pull tester is factory calibrated with equipment traceable to the NIST. It is recommended practice
to return the unit to DMC for calibration. In order to maintain traceability to NIST, do not exceed 12 months between
factory calibration intervals. The internal calibration test sequence is a reliable verification that the tester is accurate, but it
does not assure traceability to NIST.
6. TRANSPORT
It is recommended that the MPT-250B wire crimp pull tester be transported within a sufficiently sturdy box to handle the
weight of the tester and that the tester be surrounded with impact absorbing material (i.e. foam) on ALL sides in the box.
It is recommended that any accessories (i.e. grips) being transported with the tester be individually packed and wrapped in
foam to avoid damage.
7. PREVENTATIVE MAINTENANCE/ADJUSTMENT
It is recommended that the MPT-250B wire crimp pull tester be kept clean and free of debris on a daily basis using a dry
cloth.
CALIBRATION ADJUSTMENT OR MAINTENANCE IS TO BE DONE ONLY BY A CERTIFIED OPERATOR OR DMC.
No adjustment or maintenance is to be performed by end users if not certified/trained by DMC.
LIMITATION OF LIABILITY/LIMITED WARRANTY*
DANIELS MANUFACTURING CORPORATION IS NOT LIABLE FOR CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE OR
KIND RESULTING FROM THE USE OF ANY OF ITS PRODUCTS. OWNERS AND USERS OF DMC PRODUCTS ASSUME FULL
RESPONSIBILTY FOR INSTRUCTING THEIR EMPLOYEES IN THE PROPER AND SAFE USE OF SUCH PRODUCTS.
Daniels Manufacturing Corporation warrants each new unit sold by it to be free from defects in material and workmanship
under normal use and service. Its obligation under this warranty is limited to the free correction or, at its option, the refund of
the purchase price of any such unit which proves defective within ninety (90) days after delivery to the first user, provided that
the unit is returned with all transportation charges prepaid, and which shall appear to its satisfaction, upon inspection by it, to
have been defective in material or workmanship. This warranty shall not cover any damage to such products, which in the
opinion of Daniels Manufacturing Corporation, was caused by normal wear, misuse, improper operation or accident. This
warranty is in lieu of all other warranties express or implied. No warranty, express or implied, is made or authorized to be
made or assumed with respect to products of Daniels Manufacturing Corporation, other than that herein set forth.
*as defined by PL93-637
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alphatron MPT-250B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alphatron MPT-250B in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info