541398
117
Zoom out
Zoom in
Previous page
1/134
Next page
Routing 117
Software Release 2.7.1
C613-02021-00 REV F
3. Define IPX circuits
On the Head Office router define two IPX circuits, one for the Ethernet
interface and one for the wide area link. To configure the wide area link as
a demand link and enable RIP and SAP change broadcasts, enter the
commands:
ADD IPX CIRC=1 INT=ETH0 NETW=401 ENCAP=802.3
ADD IPX CIRC=2 INT=PPP0 NETW=129 DEMAND=ON
SET IPX CIRC=2 RIPCHANGE=YES SAPCHANGE=YES
Repeat this procedure on the Remote Office router, defining one IPX circuit
for the Ethernet interface and one for the wide area link. To configure the
wide area link as a demand link and enable RIP and SAP change
broadcasts, enter the commands:
ADD IPX CIRC=1 INT=ETH0 NETW=12 ENCAP=802.3
ADD IPX CIRC=2 INT=PPP0 NETW=129 DEMAND=ON
SET IPX CIRC=2 RIPCHANGE=YES SAPCHANGE=YES
The routers are now configured for IPX dial-on-demand and can exchange
routes and service information.
4. Save configuration
Save the new dynamic configuration as a script, by entering the command:
CREATE CONFIG=IPXDOD.SCP
The link is activated (the ISDN call is connected) whenever data is waiting to
transmit over the wide area link, and deactivated when no data is transmitted
over the link for a period of time. The link is also activated whenever there is a
change of route or service information, to allow the exchange of RIP and SAP
updates. To improve performance, you can configure RIP and SAP filters on
the Head Office router to limit the number and size of broadcasts which
activate the ISDN call.
To configure RIP and SAP filters, follow these steps on the Head Office
router only:
1. Create RIP filter
To create a RIP filter that only allows information about route changes to
the file server’s internal network (network number 7500) to be included in
RIP broadcasts, enter the command:
ADD IPX RIP=0 NET=7500 ACTION=INCLUDE
2. Create SAP filter
To create a SAP filter that only allows information about the file services
provided by the file server (named ACCOUNTS) to be included in SAP
broadcasts, enter the command:
ADD IPX SAP=0 SERVICE=ACCOUNTS TYPE=FILE ACTION=INCLUDE
3. Associate RIP and SAP filters with IPX circuit
To associate the RIP and SAP filters with the IPX circuit over the PPP link,
enter the command:
SET IPX CIRC=2 RIPCHANGE=YES SAPCHANGE=YES OUTRIP=0
OUTSAP=0
117


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allied Telesis AR410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allied Telesis AR410 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info