Manual Allen-Heath XB-14 (page 16 of 40) (English)

541358

Zoom out

Zoom in

1/40

Allen & Heath 16 XB-14 User Guide

OO +6

AUX

PRE

PAN

SIGNAL

PFL

PEAK

PGM

FDR

MIX B

BUS

REM MUTE

MONO INPUT CHANNEL

Aux

This control sends a signal to an auxiliary bus. The signal is sourced pre-fade

or post-fade depending on the PRE switch position. The pre-fade source

selection will be affected by the channel ON/OFF switch if active. The send

control varies the signal level to the bus from off (fully attenuated) to +6dB,

with unity gain at the arrow.

MIX B

The MIX B switch routes the channel signal to a stereo bus which is inde-

pendent of the main PGM (program) bus. The signal is post-fade and follows

the PAN control. The MIX B bus can be used for creating mixes for re-

cording or clean-feed sources for external equipment.

PAN

The pan control adjusts how the signal from the mono input channel is

shared between the left and right sides of the PGM bus and the MIX B bus.

Set to the mid position, equal amounts of signal are fed to left and right,

with pan set to L, none is sent to the Right bus.

SIGNAL & PEAK LEDs

The Signal LED illuminates when the pre-fader signal level is above –15dB.

The Peak LED illuminates and stays on for around 0.5 seconds when a peak

level is detected (pre-fader signal) within 5dB of clipping.

ON Switch

This mechanically latching switch operates the channel mute circuitry, turn-

ing the signal to the PGM, MIX B and Aux buses on or off.

The switch is illuminated green when pressed.

There is an option to disable the switch (make permanently ON) using the

option switches on the rear-panel. If this is activated, then the switch will be

illuminated green regardless of whether it is pressed or not.

There is also a remote mute option wired to a D type connector on the

rear panel. When this is wired and operated the REM MUTE red LED illumi-

nates and the mute circuit is activated regardless of whether the ON switch

is pressed.

Fader

The 100mm fader controls the level of the channel signal to the left & right

PGM bus, MIX B bus and post fade Aux.

The Mono channel faders have Fader Start switching logic available to either

interface to external equipment or activate the muting circuit for the con-

trol room speaker outputs.

PFL Switch

The PFL (Pre-Fade Listen) switch sends the channel signal to the PFL bus

and subsequently to the headphones/CRM speakers and the main L R me-

ters. Used for checking the audio signal before raising the fader or un-

muting the channel or raising the fader.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath XB-14 in the language / languages: English as an attachment in your email.

The manual is 4,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Allen-Heath XB-14 Manual

Product: