541346
27
Zoom out
Zoom in
Previous page
1/28
Next page
WZ16:2DX
AND
WZ12:2DX U
SER
G
UIDE
27
O
PTIONS
The
MixWizard Series WZ16:2 and WZ12:2DX
have a versatile architecture designed to satisfy
most live sound or recording applications you may encounter without modification. However, the
following internal options are offered to provide alternative settings for those applications that may
demand them. These options require resoldering of circuit board links and should only be carried
out by competent technical personnel. Further information is available from your service agent or
the
SERVICE MANUAL
.
P
HANTOM
P
OWER
D
ISABLE
It is perfectly safe to connect non-phantom powered sources such as dynamic microphones to
powered XLR sockets providing that balanced leads and sources are used. The +48V supply is
current limited through 6.8k ohm resistors to each XLR to prevent damage. However, you can
disable phantom power to selected channels by cutting out links on the rear connector circuit
assembly. This work should be referred to your service agent.
ST1, ST2 I
NPUT
S
ENSITIVITY
The stereo return inputs are set for nominal low level -10dBV operation as is common with much of
the external equipment available today. The console level controls let you adjust for varying input
levels. Most outboard equipment include output level trims. If, however, you wish to change the
sensitivity to high level +4dBu the rear connector circuit can be reconfigured. This work should be
referred to your service agent.
A
UX
O
UT AND
A-B O
UT
B
ALANCE
O
PTION
These outputs are impedance balanced on TRS jack to provide interference rejection when
plugged into equipment with balanced inputs. It should not normally be necessary to fit the
electronic balance option available. This option also increases the output level to a nominal
+4dBu. Refer this work to your service agent.
C
HANNEL
P
RE
-F
ADE
A
UX
S
END
O
PTIONS
The pre-fade sends are set post-EQ and post-ON as standard. However, link options on each
channel assembly allow pre-EQ and/or pre-ON if required. This is shown in the diagram below.
C
HANNEL
D
IRECT
O
UTPUT
S
OURCE
The direct outputs are sourced post-fader as standard. A link option is available per channel to
select a pre-fade source. This is shown in the diagram below.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Allen-Heath WZ16 mixwizard at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Allen-Heath WZ16 mixwizard in the language / languages: English as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Allen-Heath WZ16 mixwizard

Allen-Heath WZ16 mixwizard User Manual - German - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info